搜索资源列表
W77E516双串口演示程序
- 77E516的双串口演示程序,同样适用于77E58.双串口最佳示例代码-77E516 dual serial Demonstration Program, the same applies to 77E58. Dual Serial best sample code
win77e58
- winod77E58双串口程序-winod77E58 dual Serial procedures
lpc2194 双串口程序Def_ASM
- lpc2194 双串口程序 ,测试平台ADS1.2
avr274 AVR单片机串口通信的程序
- 这是关于AVR单片机串口通信的程序,适合与有一定基础的人看。 这份资料介绍了UART单线的软件执行。议定书的支持两个设备间的半双工通信。唯一的要求是一个输入/输出端口,支持外部中断和一个计时器比较打断。-This is on the AVR single-chip serial communication procedures, suitable for a certain basis people. This document introduces the software implement
double_uart.rar
- STC12系列双串口单片机串口转换程序,可以作为一个通用的模版,STC12 Series single-chip dual-serial port serial conversion process can be used as a generic template
c8051F040.rar
- 020与040通用双串口程序,测试过可以用,,GM 020 and 040 pairs of serial procedures, can be tested,
STC-USER-IAP-ISP
- stc系列双串口测试程序 新一代 1T 8051系列 单片机内核特殊功能寄存器 C51 Core SFRs-stc series of pairs of serial test program generation 1T 8051 Series MCU core Special Function Registers C51 Core SFRs
STC12LE_COM
- STC12系列单片机的双串口程序,接收采用串行中断方式,调试通过。-STC12 Series MCU two serial procedures, the reception serial interrupt mode, debug through.
STCDaulUart
- STC单片机双串口,串口1,2测试程序,串口2使用独立波特率发生器作为波特率发生器。-SCM STC dual serial, serial 1,2-testing procedures, using serial two independent Baud Rate Generator as the baud rate generator.
UART
- 该程序为51单片机双机串口通信程序,有接收和发送程序-The program for the microcontroller 51 pairs of serial communication program, to receive and send program
DualCOMtest
- 一个关于51单片机的双串口转换程序,两个串口之间的切换,并且接收/发送数据-On 51 single-chip dual-serial conversion process, the switch between the two serial port and receive/send data
2010-9-16
- stc12c60s2双串口通信程序 第二串口接收数据,cpu处理数据,并由串口1发送数据到控制卡,由控制卡控制led显示- STC double in series communications program 51 siglechip receive and send program.secend uarst receive data from radar.mcu deal with and send data to led control card.finally ,led con
doublestring
- STC的双串口程序,非常适合上下位机的来回控制-This is a double-string code of STC chip...
serial
- -- 本模块的功能是验证实现和PC机进行基本的串口通信的功能。需要在 --PC机上安装一个串口调试工具来验证程序的功能。 -- 程序实现了一个收发一帧10个bit(即无奇偶校验位)的串口控 --制器,10个bit是1位起始位,8个数据位,1个结束 --位。串口的波特律由程序中定义的div_par参数决定,更改该参数可以实 --现相应的波特率。程序当前设定的div_par 的值是0x104,对应的波特率是 --9600。用一个8倍波特率的时钟将发送或接受每一位bit的周期时
UART
- 单串口8051内核单片机模拟双串口程序源代码-8051 single-core single-chip serial analog dual serial source code
chuankou
- 8051与8051以及8051与PC机的串口通信程序,全双工带纠错码-8051 and 8051 and 8051, as well as PC-Serial communication program, with full-duplex error-correcting codes
double232
- 实现STC12系列双串口单片机的串口转发。其实现了串口转发后如果另一边设备因为忙而没有收到,可以再继续发送,直到发送收到应答为止。此程序转发次数门限为20次。-Achieve STC12 Series Dual serial microcontroller serial port forwarding. After the realization of the serial port forwarding as if the other side of the device is busy an
UART
- 单片机双串口程序,寄存器的设置,源代码,适用适用两个串口的应用。-SCM Two serial program, register set, the source code for the application for the two serial ports.
stc15w408as
- 利用stc15管脚切换的方式,实现双串口通信(The double serial communication is realized by the way of stc15 pin switching)
stc15双串口测试
- STC15单片机双串口测试程序 串口1串口2 使用8位可变波特率(STC15 singlechip double serial test)