搜索资源列表
曼码调制的非接触ID卡通用读卡程序编制
- 转载 曼码调制的非接触ID卡通用读卡程序编制 C语言代码程序如下: . /*H4001只读卡读码程序*/-reproduced Man Code Modulation non-contact reader ID cartoon programming with C language code is as follows :. / * Decoding CD-card reading * /
mifare读卡源码
- mifare射频卡读卡源程序--Card reading program for mifare card.
读卡
- 读卡程序,主要是非接触式读卡模块控制器程序,包含SPI通讯-reader procedures, mainly non-contact reader module controller procedures, including SPI communications
ZLG500B读卡模块数据传输协议
- ZLG500B读卡模块数据传输协议--底层函数和高级函数-ZLG500B reader module data transfer protocol -- the bottom and Senior Function Function
RFID 读卡
- 125K RFID 读卡程序
RC500 读卡程序
- MIFARE 1 读卡芯片RC500程序
id卡解码程序
- 这个是别人写的id卡读卡程序
Fm1702sl读卡芯片源代码
- fm1702读卡芯片驱动程序源码下载
预付费表读卡写卡程序
- 预付费表读卡写卡程序 使用明华的读卡器 ,Writing Table prepaid card reader to use the card reader Minghua
AT89s52RC500
- at89s52单片机与菲利普mfrc500射频读卡芯片读写射频卡资料,包括源代码,电路图以及说明文档。-at89s52 SCM and Philip mfrc500 RF radio frequency card reader chip to read and write data, including source code, schematics, and documentation.
SD
- sd卡的程序,上面记录了SD卡的详细读卡写卡方式,适合51单片机或者其他-sd card procedures, the above records the SD card reader to write in detail the way cards for 51 single-chip or other
RFIDreaderprogram
- RFID读卡程序。硬件工作原理:基站在上电的情况下通过耦合线圈发射频率为125k的正弦波,ID卡的耦合线圈在125k的正弦波的激励下产生感应电动势,它为整个ID卡提供电源。ID卡通过调制电路根据其卡类的数据使ID卡的耦合线圈也发出正弦波,基站的耦合线圈接收到,根据它与125k波的不同来表示不同的数据。并将其通过DATA端以曼切斯特码的形式输出。-RFID reader program. Hardware it works: At the base station on the case of e
H4001
- ID 卡读卡程序,这是个比较经典的读卡程序,读头是两个TTL芯片组成-Read the ID card program
id
- 基于stc11f08xe的125KHz ID读卡器程序,读卡的ID号通过串口发送-Based stc11f08xe of 125KHz ID card reader program, ID number sent through the serial port
程序源码
- 驱动ID卡读卡模块的程序,通过串行口输出ID号。(Drive ID card reader module program, through serial port output ID number.)
RFID_Project
- 利用飞思卡尔的KL25Z128处理器、EM4095射频读卡模块、显示模块、存储模块和实时时钟等模块;软件设计使用IAR for ARM 6.4开发环境,通过编程实现对系统硬件的初始化、数据的编码、解码、存储和显示、以及对数据的无线发送,(Using KL25Z128 processor, EM4095 RF fly Si Carle card reading module, display module, storage module and real-time clock module; so
RFID读卡模块电路图、PCB源文件
- 125K RFID读卡模块,包含UART输出,韦根输出,程序中,根据曼彻斯特原理,找到长电平和短电平,根据跳变沿分析出0数据还是1数据。然后寻找消息头,后面的数据进行 行 列奇偶校验,从而分析出卡号。(125K RFID card reader module, including UART output, Wei root output, in the program, according to the principle of Manchester, to find a long level
FM175XX_MifareCard读卡参考代码
- 复旦微电子的非接触读卡IC17520及17550读卡例程,例程使用51单片,可读ISO14443A、ISO14443B的卡片。包括M1卡、CPU卡.身份二代证的UID....(Fudan Microelectronics non-contact reading card IC17520 and 17550 card reader routines, routines using 51 single-chip, readable ISO14443A, ISO14443B cards. Includ
Mifare卡读卡器整套资料
- 实现mifare读写,全部代码,在vc上测试ok(test mifare read and write is succesful so you can test in vc ide hh aa bb cc dd)
读卡程序
- 自己编写的rc522读卡程序,已经验证,运行ok,硬件是正点原子的精英版(I wrote the rc522 read card program, has been verified, run OK)