搜索资源列表
1总线通信协议应用实例
- 1总线通信协议应用实例-a bus communication protocol Application
单片机C51串口中断接收和发送测试例程(含通信协议的实现
- 单片机C51串口中断接收和发送测试例程(含通信协议的实现)
RS232串口通信协议
- RS232串口通信协议,verilog实现,通过FPGA完全调通。,RS232 serial communication protocol, verilog achieved entirely through the FPGA transfer pass.
urt.rar
- C8051F带通信协议的串口通信通信程序,上位机发送0xAA,单片机收到后反馈0xBB,通信开始。通信结束后发送0xCC。,C8051F serial communication with a communication protocol of the communication program, host computer to send 0xAA, SCM receipt feedback 0xBB, communication began. Communications sent afte
usb
- 基于单片机的USB通信程序,包括完整的通信协议-SCM USB-based communication program, including a complete communication protocol
infrare-dmeter-demo
- 红外抄表系统的源代码。利用非电信号传送控制信息和数据信息,以实现遥控或遥测的功能。包括 通信方式,通信协议,三相电度表通信程序,手持抄表器通信程序等。-Infrared meter reading system s source code. The use of non-electrical signal transmission control information and data information in order to achieve remote control or tele
VCProgram
- 本人用VC6.0开发的单片机通过串口与PC机通信的上位机,通信协议在说明文档中已经写出,用户在单片机上编写串口函数时按照通信协议,便可以很方便通过此软件与PC机通信.-err
c51uart_test
- 单片机C51串口中断接收和发送测试例程(含通信协议的实现)-C51 single-chip serial port receive and transmit interrupt routine test (including the realization of communication protocols)
biyelunwen
- 随着计算机技术的不断发展,USB设备以其传输速度快、可热插拔、独立供电等诸多的优点被普遍采用。现在市面上的USB设备层出不穷,如U盘、MP3、移动硬盘等应用起来十分方便。 本文采用VisualC++6.0软件进行仿真,利用基于对话框的VC++应用程序完成对上位机界面的编写,可以利用VC编程实现对计算机底层硬件的操作。采用DriverStudio软件编写USB设备的驱动程序。 本文先介绍了USB通信协议及其传输方式,然后具体地给出了驱动程序开发的全过程,同时根据硬件电路设计了上位机显示
modbus
- 基于51单片机的MODBUS通信协议,单片机作为主站,读取从站信息-Based on 51 SCM MODBUS communication protocol, microcontroller as the main station, read the information from the station
SimpliciTI-1.0.3
- simpliciti1.0.3版本,IT公司自定义的简单无线通信协议,包括多个实验程序-simpliciti1.0.3 versions, IT companies from the definition of a simple wireless communication protocols, including the number of experimental procedure
C51 MODBUS通信协议实现
- 基于C51的modbus通信协议实现,C程序,绝对能够使用
STC89C52基于can的温度测量
- 将CAN总线通信应用于单片机中,使得多极芯片之间可以互相连接,程序内包含CAN通信协议及接收发送功能。(The CAN bus communication is applied to the single chip microcomputer, so that the multi chip chips can be connected with each other, and the program contains the CAN communication protocol and the
DLT645-2007多功能电能表通信协议调试器本
- DLT645-2007多功能电能表通信协议调试器(DLT645-2007 multifunction energy meter communication protocol debugger 2011-03-21 release)
Modbus
- 使用STC15F2K602S 实现了Modbus通信协议。 本Modbus程序实现了保持寄存器区32个功能寄存器64字节的读写功能,可用于实现32个int型数据的通信 写寄存器支持单个寄存器的写指令 使用功能号06 如:01 06 00 00 00 08 88 0C 读寄存器支持多个寄存器都指令,使用功能号03 如:01 03 00 01 00 01 D5 CA 方便朋友们直接移植到其他单片机 里面附带TA6932的显示驱动,将寄存器的内容显示在6932驱动的LED上(Th
车载lin通信协议V2.0中文版
- 车载LIN v2.0协议,详细说明了协议帧格式,同步,校验和计算等。对于需要进行LIN协议开发非常有用(LIN2.0 protocol Detailed descr iption of the protocol frame format, synchronization, check and calculation and so on. It is very useful for the development of LIN protocol development)
关于IIC的通信协议程序
- 关于IIC的通信协议程序,深入浅出,简单易懂。(Communication protocol program on IIC,It is simple and easy to understand.)
Arduino和CSharp通讯
- LED 串口控制 Arduino和CSharp通讯 通信协议,单片机 Arduino开发板通信(LED serial port control Arduino and CSharp communication and communication protocol, MCU Arduino development board communication)
匿名科创地面站及通信协议
- 匿名科创地面站及通信协议 可以实现数据波形显示。姿态显示等。(Anonymous science creation ground station and communication protocol can realize data waveform display. Posture display and so on.)
通信协议FPGA
- 本设计是基于FPGA的高速并行接口通信接口和协议设计,该设计使用的是8 位并行接口,通过配置FPGA的FIFO寄存器保证了在高速并行下的数据稳定性,在 最终的测试中,该协议能够稳定传输的速度为80Mbps。(This design is based on FPGA high-speed parallel interface communication interface and protocol design, the design uses 8 Bit parallel interface