搜索资源列表
MCS51
- 本人自己写的经典51程序完全好用。包括7279,液晶,297,298等外设具有很高的参考价值
DS1302时钟芯片C例程
- /*这个程序,是我用51电子网http://www.51dz.com/n.asp?id=12519&i=xie343706382,298元C51学习板调试通的单片机控制DS1303时钟芯片试验时请用排线 将p1口连到CZ2 一个时钟程序,它能实现断电走时(用纽扣电池),显示和设置年月日星期时分秒(8位数码管)。 */
l297l298
- 基于C8051F330,L297/298步进电机控制程序,实现步进电机的正反转,加速减速,以及数码管显示转数。-Based on the C8051F330, L297/298 stepper motor control program, to achieve positive stepper motor to speed up slow down, as well as to the number of digital tube display.
L298
- 基于ARM7的L298驱动程序,芯片L298,控制两个直流电机,没有用PWM调速-Based on ARM7-L298 driver chip L298, control two DC motors, there is no speed control with PWM
ds
- 这是我看了《十天学会单片机》(郭天祥的教程)/*这个程序,是我用51电子网,298元C51学习板调试通的单片机控制DS1303时钟芯片试验时请用排线 将p1口连到CZ2 一个时钟程序,它能实现断电走时(用纽扣电池),显示和设置年月日星期时分秒(8位数码管)。 */(http://www.51dz.com/n.asp?id=12519&i=xie343706382)测试时请将p1口用排线连到CZ2上,控制8位 数码管用。P0口用来检测矩阵键盘的,P3.0和P3.1是串口通信用,控制
dzb
- 这是我看了《十天学会单片机》(郭天祥的教程)第十课时写的,综合了矩阵键盘,串口通信,数码管 动态显示,定时器中断的简单时钟程序。用51电子网买的298元80C51单片机学习板 (http://www.51dz.com/n.asp?id=12519&i=xie343706382)测试时请将p1口用排线连到CZ2上,控制8位 数码管用。P0口用来检测矩阵键盘的,P3.0和P3.1是串口通信用,控制74H164N芯片段选8位数码管。 数码管显示内容为时分秒个两位,按下K16为设置按钮,
298
- l298资料,有很多,值不值看看了就知道 -L298 material, there are many, worth looking knewL298 material, there are many, worth looking knew
pin
- 小车红外避障 驱动直流电机 38khz红外 小车拐弯、前进功能-IR obstacle avoidance car driving DC motors 38khz infrared car turning, forward function
motor
- 这是一段控制步进电机转动的代码。希望对搞电机的同行有所帮助。驱动芯片是297+298-this is a code for controlling the step motor.
PWM
- 单片机利用PWM信号控制直流电机调速 接L298N时相应的管脚上最好接上10K的上拉电阻。 -Microcontroller using PWM signal control DC motor speed access L298N best when the corresponding pin of the pull-up resistor connected to the 10K.
TheCarProcedures
- 以C8051f020单片机为核心,TCRT5000和393作为寻迹模块,1602为显示屏,298为驱动模块的运水机器人小车程序-To C8051f020 MCU core, TCRT5000 and 393 as a tracing module, 1602 for the display module 298 for driving robot car carrying water program
629_298test
- 430+629的机器人代码,也调试成功-430,629+298
l297l298
- 本程序基于C8051F330,L297/298的步进电机驱动程序,P1.1 控制L297使能位ENBLE,P1.2 控制连L297 CCW口控制电机正反转-L297 L298 C8051
20
- 298驱动步进电机控制程序,附有电路原理图,详情注解.-298 drive stepper motor control program
298
- 单片机89s52通过控制l298来驱动两个电机转动,并且通过PWM调节来控制转速。-L298 microcontroller 89s52 to drive through the control two motor rotation, and through the PWM regulator to control speed.
sadf
- 使用298作为驱动芯片实现小车的避障功能-As a driver chip with 298 car obstacle avoidance capabilities
298
- 直流电机交流电机的驱动芯片和代码L298-Motor drive Motor drive Motor drive Motor drive Motor drive Motor drive