搜索资源列表
Motocontrol
- 电机速度控制 RA0 RA1速度控制. RA2伺服输入 .报警输入RA3.-RA0 RA1 speed control motor speed control. RA2 servo input. Alarm input RA3.
pic_AD
- PIC单片机AD转换汇编程序,A/D采用中断方式。该程序通过单片机的RA2模拟通道送入 一直流电压，当送入的直流电压大于2.5V时，8个LED闪动，当直流电压恢复到2.5V以下时，LED停止闪动。为了防止干扰，本程序对直流电压采样10次后再作判断，中间的采样结 果用间接寻址的方式存取。 -for PIC ad control
picAD
- PIC16F877A自带A/D模块应用测试 FileName :picAD.c CPU :PIC16F877A Function :RA2作模拟输入口，RD2口指示采样转换数据变化-PIC16F877A own A/D module application testing FileName: picAD.c CPU: PIC16F877A Function: RA2 for analog input port, RD2 mouth convert data sample cha
AD
- 程序实现A/D转换功能，A/D采用中断方式。该程序通过单片机的RA2模拟通道送入一直流电压
Motorcontrl
- 一个简单的马达控制程序。速度控制. RA2伺服输入 .报警输入-SIMPLE SPEED CONTROL SOFTWARE TO CONTROL MOTOR & REVERSING RELAY
AD
- 程序实现A/D转换功能，A/D采用中断方式。该程序通过单片机的RA2模拟通道送入一直流电压，当送入的直流电压大于2.5V时，与PORTD口相连的8个发光二极管闪动，当直流电压恢复到2.5V以下时，发光二极管停止闪动，且只有低四个发光。-Program for A/D conversion, A/D with interrupt. RA2 through the program the microcontroller analog channels into a DC voltage into D
counter
- Modify the solution of question 1 to have a down/up counter as follows: · RA2= 0 Counter is disabled. · RA2= 1 Counter is enabled: o If there is negative edge signal at pin RA3 then counter counts up. o If there is negative edge signal at pin
AD
- PIC AD转换程序实现A/D转换功能，A/D采用中断方式。该程序通过单片机的RA2模拟通道送入一直流电压-pic ad change
AD
- PIC16F887A单片机A/D转换程序，RA2接AD模拟电压，当输入电压大于2.5V时发出报警型号，与PORTD相连的8个LED数码管闪烁；当电压小于2.5V时，发光管停止闪烁，且只有低4个发光 。-The the PIC16F887A microcontroller A/D conversion process, RA2 then AD analog voltage alarm when the input voltage is greater than 2.5V Model 8 LED d
PIC-ccp
- //比较器的工作模式：CM2－CM0＝011,交流信号经半波整流送至C1的负端RA1， //参考电压模块产生一个0.63V的电压输出到C1的正端RA2，C1的输出为引脚RA5。 -//Comparator mode: CM2-CM0 = 011, the half-wave rectified AC signal to the negative terminal of C1 RA1,// 0.63V voltage reference module gener