搜索资源列表
电机驱动电路
- 电机驱动电路
初始化鼠龙电机的 deep影响 bar
- 在电机分析中,注意考虑深鼠龙条的影响。
电机限时运行S7-300.rar
- 电机限时运行S7-300.rar---上位机设置电机运行时间。
PROTEUSEXAMPLE.rar
- 关于proteus的仿真实例,很不错的,包括流水灯、步进电机等等。,About Proteus simulation examples, very good, including the water lamps, stepper motor and so on.
xinxin.rar
- 对直流电机进行调速,通过三个开关控制电机的正传,停止,反转,DC motor speedcontroller
yibudianjifangzhen.rar
- 电机系统仿真,主要基于matlab的电机仿真程序,Electrical System Simulation
jy_TestMotor
- 义隆的8bitMCU。78P153控制步进电机系统。-Elan s 8bitMCU. 78P153 controlled stepper motor system.
8255bujingdianji
- 用单片机实现8255控制步进电机,其中可控制转速和转动方向 -With MCU 8255 stepper motor control, which can control the speed and rotational direction
电机转速计算
- 采用labview编写的电机转速计算器,输入轮胎直径 、减速比、要求车速,输出所需电机转速(Written by LabVIEW motor speed calculator, enter the tire diameter, speed reduction ratio, speed requirements, the output motor speed required)
直流电机位置控制
- 直流电机位置控制,前面板设置电机指针位置,运行程序,电机即可按照预设值转动。(DC motor position control, the front panel set the motor pointer position, run the program, the motor can be rotated according to the preset value.)
电机正转
- 单片机控制直流电机的正转,通过l298n来做到非常简单的同时实现2个直流电机的功能(The direct rotation of DC motor controlled by single chip microcomputer)
同步电机滑模和协同
- 可以放入电机模型,直接运行,改变参数比较方便(Can be put into the motor model, direct operation, change the parameters more convenient)
直流电机控制源代码
- 通过前馈控制直流电机运转,并生成pwm波形进行检测(Feedforward control of DC motor)
Labview_并口控制步进电机
- 步进电机联机控制,将通讯电缆连接到计算机的COM1与控制器的RS-232口,再打开控制器的电源开关并设置好联机,最后打开上位机界面,(The control resource, data type, data analysis and processing library function are used to realize automatic measurement of control system. It mainly collects light intensity signals
步进电机控制
- 能够使用arduino uno r3来通过步进电机控制器,实现步进电机旋转角度及旋转速度的控制(Arduino uno R3 can be used to control the rotation angle and speed of stepping motor by stepping motor controller.)
8086步进电机(按钮控制)
- 基于8086的汇编步进电机多段速按钮控制(Step motor button control)
stm32f103rct6步进电机freeRTOS掉电保存
- stm32f103rct6步进电机 基于freeRTOS 掉电存储(stm32f103rct6 stepper based freeRTOS)
ADC0809控制直流电机
- ADC0809控制直流电机经过CPU通过DAC0832输出(8086;ADC0809;DAC0832;assembly)
基于LabVIEW的电机控制系统
- 基于LabVIEW的电机控制系统。包括:直流电机闭环,永磁同步电机控制,电机转速调试,步进电机控制,电机调速器等。适合相关从业人员交流学习。(The motor control system based on LabVIEW. Including: DC motor closed-loop, permanent magnet synchronous motor control, motor speed debugging, stepper motor control, motor governo
拉力传感器电机控制
- 数据采集卡采集拉力值,与预先设定的拉力值进行比较,然后PID运算,控制相应的PWM占空比输出,最终控制电机的速度(The data acquisition card collects the pull value and compares it with the pre-set pull value. Then the PID arithmetic is used to control the output of the corresponding PWM duty cycle, and fin