搜索资源列表
PN_GenerateAndCompare
- 产生PN23码,并可以检测传输过程中的误码率-have PN23 code, and can detect the transmission error rate
noiseMSK
- 带有高斯白噪声的MSK的调制,连续相位调制以及误码率分析和眼图分析-with Gaussian white noise of MSK modulation, continuous phase modulation and error rate analysis and eye diagram analysis
DECMMSE
- 解相关DEC和MMSE误码率曲线对比,包含LMS算法,以及硬判决-decorrelation DEC and MMSE BER curves contrast, contains LMS algorithm, and the hard decision
clipping_ber_4qam
- clipping算法的误码率仿真文件,通过matlab仿真
BER_MAI10K10M6_compare_Gold_Uplink
- 本程序是几种基本的检测算法的误码率性能的比较
mskgmskbfsk
- 包中详细架构了BFSK MSK GMSK调制系统 和误码率分析-BFSK MSK GMSK
juanjima
- 仿真(2,1,2)卷积码编解码器在二进制对称信道(BSC)中的误码性能,画出纠错后误码率-信道误码率曲线,其中,编码器的生成多项式为g1=[111]、g2=[101]。-imulation (2,1,2) convolutional encoding and decoding the binary symmetric channel (BSC) in the error rate performance, bit error rate after correction drawn- the ch
ofdm
- OFDM在MATLAB中的仿真程序,包括数据生成,数据传输,干扰,误差补充,数据接收,误码率的计算。不过误码率很大,达到0.5,希望对大家有用。-OFDM in the MATLAB simulation program, including data generation, data transmission, interference, error added, data receiving, the bit error rate calculations. But a large erro
PSK8_T1_R1
- 8PSK误码率分析 误码率(BER:biterror)是衡量数据在规定时间内数据传输精确性的指标。误码率=传输中的误码/所传输的总码数*100 。如果有误码就有误码率。 -8PSK analysis of bit error rate BER (BER: biterror) is a measure of data in the time indicator of the accuracy of data transmission. Bit error rate of BER = trans
QPSK_system_BER_simulation
- 进行QPSK的BER算法的仿真,计算误码率-The BER for QPSK simulation algorithm to calculate the bit error rate
jiexiangguang_multiusers
- 基于多用户下的JXG误码率,MATLAB-Based on multi-user bit error rate JXG under, MATLAB
74xunhuanbianmawumalvfenxi
- 对(7,4)循环码的误码率进行了matlab的仿真,通过对比两条曲线,直观对比出未经过信道编码和经过信道编码的误码率比较。-Of (7,4) cyclic code error rate of the matlab simulation, by comparing the two curves, a direct comparison has not been after channel coding and channel coding the bit-error rate.
Matlabviterbilenwu
- 本课程设计主要解决对一个卷积码序列进行维特比(Viterbi)译码输出,并通过Matlab软件进行设计与仿真,并进行误码率分析。在课程设计中,系统开发平台为Windows Vista Ultimate,程序设计与仿真均采用Matlab R2007a(7.4),最后仿真详单与理论分析一致。-viterbi
Fig6and7
- 进行空时分组码的编译码仿真,仿真出不同信噪比下的性能,得出误码率曲线。-For space-time block code encoding and decoding simulation, simulation performance under different signal to noise ratio obtained BER curves.
Fig8and9
- 空是分组码的编译码程序,得出误码率曲线图,很好用哦-Space is the block code encoding and decoding procedures for error rate curves obtained, very good with the oh
1
- 卷积码维特比译码器设计输出完整电路进行误码率分析-Convolutional code Viterbi decoder integrated circuit design of the output bit error rate analysis
123456
- 蒙特卡罗实验,计算误码率。为书上的程序。可以参考-Monte Carlo experiment to calculate the error rate. Procedures for the book. Can refer to
rayleiBPSK
- 在瑞利信道下,进行了BPSK调制,得到信号的误码率仿真曲线。-In Fading Channel, conducted a BPSK modulation, the BER of signal simulation curve.
student_error_detect 1
- 简单的实现比特序列误码率计算,使用的都是很基础的原件,并未使用现成的误码率计算文件(A simple way to computes the bit error rate of a bit sequence.)
基于高斯白噪声信道BPSK调制下的误码率与信噪比的关系
- MATLAB代码 公式推导的时候信噪比的单位是B,目的是为了推导的方便,代码在写的时候需要记得换算。 单个符号的比特数跟信噪比有关,snr越大,其越大。 由于符号1被误认为是0的概率与符号0被误认为是1的概率是一样的,因此无论蒙特卡洛的仿真次数是多少,误码率的理论计算值 与蒙特卡洛仿真值永远一样!(条件是高斯白噪声为0均值的) 为了让实际结果与理论值完全一样,高斯白噪声的概率密度函数中的均值需要为0!但是这个条件在实际生活中无法满足。 环境是不能改变的,因此噪声的均值是无法改变的。