搜索资源列表
111
- 1 .手机屏幕尺寸为 w = 240 h = 320，现提供LCD BUF(type:unsigned short)的起始地址为lcdbuff。要求从坐标(100,10)处开始绘制一条长度为300的黑色(颜色值为0)垂直线。 参考代码： 2 .在第1题的基础上封装一个画垂直线的函数，不考虑颜色。 参考代码： 3 .在第1题的基础上封装一个画水平线的函数，颜色可不考虑。 参考代码： -The start address of a mobile phone scr
sheet6578066
- str lentght decoder to show i for glcdmages on LCD for avr
OneWire
- This code demonstrates one-wire communication with temperature sensor DS18x20 connected to RD0 or RA5 pin. unit reads temperature from the sensor and prints it on the LCD. The display format of the temperature is xxx.°C . To obtain correct
yejingpingsheji
- 本篇文章介绍了液晶屏的设计，从传统指令方式读写改为总线地址方式读写，具有一定的参考价值。-This article introduced the LCD screen design, from the traditional command mode read/write to address bus read and write, has a certain reference value.
LC
- 本系统是以FPGA（EP2C8Q240C8）为控制核心，由压控振荡器、PLL倍频器、高频功率放大器、遥控器及LCD显示模块组成的压控LC振荡器。能实现输出正弦波频率在15MHZ~35MHZ步进可调，其最小步进为5002HZ，频率稳定度为10-5。当输出信号的频率为30MHZ、峰峰值稳定在1V左右时，在+12V单电源工作的情况下，功率放大器能实现在50Ω纯阻性和50Ω+20pf容性负载上输出功率大于20mw。LCD显示模块能实时显示输出信号的峰峰值和频率，精度由于10 。-This system
lcd2vga
- 需要arm的lcd输出转VGA的童鞋值得一看的东东！-arm s lcd output switch to the VGA, Newbie recource!
HT48-a-HT46-LCM
- HT液晶模块接口设计 本文介绍利用8 位微控制器控制DV16100NRB液晶显示驱动器的方法-HT LCD Module Interface Design This article describes the use of 8-bit microcontroller to control DV16100NRB LCD drive
HT67F40-C
- HT67Fx0内建有R/C-Type LCD功能，可提供1/2或1/3 Bias、4个COM的驱动能力，本文以HT67F40为母体，给出1/3 Bias、1/4 Duty的LCD驱动的使用方法-HT67Fx0 built R/C-Type LCD function, can provide 1/2 or 1/3 of the Bias, 4 COM-drive capability, to HT67F40 for the mother is given a 1/3 of the Bias, 1/
YB12864ZC(1)
- LCD屏硬件原理图与相关资料与使用说明书-Hardware schematics and related information to the LCD screen and manual
display_driver
- SSD1963 is a display controller of 1215K byte frame buffer to support up to 864 x 480 x 24bit graphics content. It also equips parallel MCU interfaces in different bus width to receive graphics data and command from MCU. Its display interface sup
cat6612
- The CAT6612 is a high-performance and low-cost single channel HDMI transmitter, fully compliant with HDMI 1.2, HDCP 1.1 and backward compatible to DVI 1.0 specifications. The CAT6612 serves to provide the most cost-effective HDMI solution for DTV-rea
I2C-BUS-Specification(Chinese)
- I2C 总线是一种用于IC 器件之间连接的二线制总线。它通过SDA（串行数据线）及SCL（串行时钟线）两根线在连到总线上的器件之间传送数据，并根据地址识别每个器件：不管是单片机、存储器、LCD 驱动器还是键盘接口。I2C 能用于替代标准的并行总线，能连接各种集成电路和功能模块。支持IIC 的设备有微控制器、ADC、DAC、储存器、LCD 控制器、LED 驱动器以及实时时钟等。采用I2C 总线标准的单片机或IC 器件，其内部不仅有I2C 接口电路，而且将内部各单元电路按功能划分为若干相对独立的模块
xd-stm32-13
- 芯达STM32入门系列教程之十三《点亮LCD液晶屏》-Core up to STM32 Getting Started tutorial series of thirteen " lit LCD screen
Display_Port_1.2
- 液晶顯示器相關接口知識實現edp的最終點屏-LCD display interface knowledge to achieve a the edp final point screen
TFT_Init
- Please help me. I want to integrate TFT LCD display with LPC1766. I want to display text on 2.8 inch TFT LCD
TFT240320-demo
- TFT LCD code demo HARDWARE AVR mega8,16,32 BL-TFT240320PLUS. An interface can be 8/16 bit mode. TFT LCD arduino shield. SD card File APPLICATION main.c main program. scan SD card and display BMP file on lcd. readm
znpqs
- 本智能排气扇以STC12C5A08S2为核心控制单元，通过远红外传感器探测热水器加热火焰来判定热水的开停。采用抗干扰能力强，精度高的数字温度传感器DS18b20感知温度，结合晶闸管BT136，实现无级调速。系统通过1602液晶把温度、湿度，转速等实时信息反馈给使用者。使用者也可通过键盘实现排气扇的本地控制。本设计通过霍尔传感器进行转速的采集，进而实现排气扇卡死等故障的自我检测。-The smart exhaust fan to STC12C5A08S2 as the core control u
ok
- 用fpga的lcd显示汉字云南大学……，寄存器写数字符码-To fpga' s lcd display Chinese characters Yunnan University ... register to write a few character code
Nokia5510-Display-DRV
- Nokia5510显示屏驱动程序,方便初学者了解如何编写LCD的驱动程序。-Nokia5510 display drivers, easy for beginners to learn how to write the LCD driver.
ADCDisplayPrototype
- Displays the value of an analog inputs to LCD