搜索资源列表
电子脉搏计设计
- 一.设计题目:电子脉搏计设计 二.主要内容及安排 脉搏测试仪是用来测量一个人心脏跳动次数的电子仪器,也是心电图的主要组成部分。它是用来测量频率较低的小信号。 (1)实现在15S内测量1min的脉搏数; (2)用数码管将测得的脉搏数用数字的形式显示; (3)测量误差小于±4次/min。 (4)设计电路,在时间允许的情况下要安装测试,分析实验结果,写出设计说明书。 三、安排进度 6月12号:图书馆收集资料 6月14号:互联网收集资料 6月28号:资料的整理
八段数码管显示
- 80C51和74LS164驱动八段数码管显示
SM420364
- 8段数码管,为SM420364封装,包括引脚,以及其他的数码管介绍。-8 digital tube, SM420364 package, including a pin, and other digital tube is introduced.
vhdprograme
- 用vhdl做得CPLD静态两位数码管扫描 显示“10”两位数码管公用段选-CPLD with VHDL done two static scan digital tube displays
ds18b20
- ds18b20实现温度采集,并显示在数码管上 -temperature ds18b20 collection, and display in the digital tube
7segment
- 这是7段数码管的接口PPT说明。还有一些ADDA部分的讲解。注:PPT文档。-This is a 7-segment digital tube interface PPT instructions. Explain some part of the ADDA. Note: PPT document.
BCD
- 硬件应用,用BCD译码数码管显示数字,数码显示-Decoding digital display digital
shumaguan
- 单片机C语言程序设计实训之数码管显示的频率计-Digital display of frequency counter
msp430f149
- 要求用两位共阴数码管显示,P0口控制abcdefg,dp,P2.01控制位选-Asked to use two common cathode LED display, P0 port control abcdefg, dp, P2.01 control Choice
clock1
- 用VHDL编程实现在数码管上动态显示时间 功能有整点报时 自动设置时间-VHDL programming in the dynamic display of the time function of the whole point of time is automatically set time on digital tube
danpianjishumaguanchenxu
- 单片机控制数码管0到100的自加显示程序-SCM digital tube 0-100 plus display program
clocka
- 时间可调的小程序,带有按键扫描。数码管动态显示。-Time is adjustable small program with key scan. Digital dynamic display.
FPGA_-digital-pipe-articles
- 手把手教你学习FPGA—数码管篇,带你轻松走进FPGA的世界!-Taught you learn FPGA-digital tube articles take you easily into the FPGA world!
main
- 将两块CAN总线开发板CANH---CANH,CANL---CANL相连连接无误后分别按动中断按键。相应的数码管显示加一,并通过CAN总线发送到另一块数码管上显示。-Two CAN bus development board CANH--- CANH, CANL--- CANL connected connected to the correct respectively pressing the interrupt button. Corresponding digital display p
main
- CAN开发板-CAN自收发实验,数码管从右到左分别是1~4位。数码管1、2位显示发送的数据,3、4位显示接收到的数据。每按一次中断按键发送数据值增一。--CAN CAN development board self-transceiver experimental digital tube from right to left are 1 to 4. 1,2 bit digital tube display data sent, 3,4-bit display data received. Ea
main
- 将两块CAN总线开发板CANH---CANH,CANL---CANL相连,通过串口调试软件发送数据到单片机中,数码管显示相应的数值,并通过CAN发送到另一块CAN开发板上。-Will be connected to two CAN bus development board CANH--- CANH, CANL--- CANL debugging software to send data through the serial port to the microcontroller, digit
MCU-COMMUNICATION
- 单片机双机通信 以及数码管显示 可随便修改-MCU communication
Text1
- 单片机控制数码管,秒表与毫秒表计数,毫秒表满10进一秒,满60秒,清零,继续计时-the disign of millsecondmeter and secondmeter,controlled by scm
cepin.tar
- 这是我自己用FPGA做过的等精度测频的主体思路,包括主要代码,没有数码管显示部分。肯定能用。-This is done for my own use FPGA and other precision frequency measurement of the main ideas, including the main code, there is no digital display section. Certainly can.
cexiangwei
- 这是我写的相位测试仪中相位测试的主要代码,有相位测试的主要思路,不包含数码管显示部分。-This is what I wrote in the phase test phase tester main code, the main idea of the test phase, does not contain the digital display section.