搜索资源列表
SDA7123
- SDA7123是一个三路高速、数模转换器的单片集成电路。它包括三路高速、 10位输入的视频 DA转换器、标准的 TTL输入 和互补输出高阻抗的模拟输出电流源。-SDA7123 a three-way high-speed, monolithic DAC. It includes three-way high-speed, 10-bit input video DA converter, a standard TTL input and complementary outputs the anal
STM32-TIM1-PWM
- 通过对 TIM1 定时器进行控制,使之各通道输出插入死区的互补PWM 输出, 各通道输出频率均为17.57KHz。 其中,通道1 输出的占空比为50 ,通道2 输出的占空比为25 ,通道3 输 出的占空比为12.5 。各通道互补输出为反相输出。 TIM1 定时器的通道1 到3 的输出分别对应PA.08、PA.09、PA.10 引脚,而通 道1 到3 的互补输出分别对应PB.13、PB.14 和PB.15 引脚,将这些引脚分别接 入示波器正接线,GND 引脚接示波器负接线,
M051-PWM
- M051的PWM呼吸灯输出以及半桥互补输出,寄存器操作,接近C51程序-M051 PWM respiration lamp and half-bridge complementary output
pwm
- PWM VHDL程序,双路互补输出,精度占空比可调-PWM VHDL program, dual complementary output, precision adjustable duty cycle
AVR-Digital-Amplifier
- 基于AVR ATmega8 的小功率数字功放 音频经过LM358,然后送入单片片ADC, 模数转换后数字信号通过OC1B OC1A互补输出,驱动三极管 -Based AVR ATmega8 small power digital amplifier Audio through LM358, then into a single piece of ADC, After the analog to digital conversion of digital signals t
tim1
- stm32F205两路带死区的互补输出的程序,主要功能是,逆变控制使用,频率可调,死区大小可调。功能强大,-stm32F205 timer
搞定_ STM32 TIM1输出互补波形 加 详细中文注释
- 搞定_ STM32 TIM1输出互补波形 加 详细中文注释(STM32 output complementary PWM wave)
高级定时器输出1路互补 PWM实验---含详细注释
- 基于STM32单片机设计的高级定时器TIM1的6路互补带死区的PWM输出实验,代码中含有详细的注释,对学习PWM很有帮助(STM32 microcontroller based design of advanced timer, TIM1 6 complementary band, dead zone PWM output experiment, the code contains detailed notes, helpful for learning PWM)
STM32-M0-PWM互补输出和死区插入
- 利用STM32F031单片机产生六路相同频率具有死区时间的PWM,本程序可以用来做BLDC的参考(The use of STM32F031 microcontroller produces six same frequency, with dead time PWM, this procedure can be used to do BLDC reference)
互补PWM输出-完整版
- 蓝桥杯模拟互补PWM输出-完整版,完成题设所有要求(Blue Bridge Cup simulation complementary PWM output - Full Version, complete all the requirements of the problem set)
1 PWM高级定时器互补输出
- STM32高级定时器实现互补输出通过RC震荡电路输出正弦交流电,实现直流转交流。两个通道之间存在一个死去时间。(The STM32 advanced timer implements complementary output through the RC oscillating circuit to output sinusoidal alternating current to achieve direct flow communication)
三对6路PWM带互补带死区
- 应用stm32f103 输出6路pwm信号 还有互补和死区......(Application stm32f103 output 6 pwm signal there are complementary and dead zone)
TIM1_PWM 互补输出
- 配置TIM1的互补输出模式,输出两路互补的PWM波。(The complementary output mode configuration TIM1,PWM wave output two complementary.)
6路spwm输出有死区控制
- 输出六路互补的SPWM波形用于SPWM的控制(use the SPWM to control)
STM32 的4路互补pwm
- 使用keil5编写的STM32输出四路互补的PWM,适配正点原子的mini版,同样是为电赛逆变系统做的准备。通过定时器的输出比较模式,在PC6~PC9,输出4路PWM,每路PWM频率为500Hz,占空比为50%,每一路PWM相位差为45°(The STM32 output four complementary PWM, which is written in keil5, is suitable for the mini version of the positive point atom, w
正点原子PWM
- stm32f4输出互补pwm波,用于电机,变频器的驱动。(Stm32f4 output complementary PWM wave.)
stm32 pwm输出
- TM32的高级定时器TIM1可以产生互补的PWM,并且可以通过相关寄存器的设置使能或关闭PWM的输出。在编写BLDC的驱动程序时,本人利用TIM1的channel1,2生成了三路互补的PWM波形,定时器驱动程序(The advanced timer TIM1 of TM32 can generate complementary PWM, and it can enable or close the output of PWM through the setting of related regi
STM32SPWM实现
- 用STM32F103 实现三相互补输出 SPWM波,可调频率,串口通许控制,已经上机调试成功(Using STM32F103 to realize three phase complementary output SPWM wave, adjustable frequency and serial port control, it has been debugged successfully.)
SPWM_双极性_TIM8互补输出
- 此为使用STM32单片机产生两路双极性互补SPWM波的程序,注释详实,直接可以烧录使用,看程序找到对应管脚接上即可。(This is the use of STM32 microcontroller to produce two channels of bipolar complementary SPWM wave program, detailed notes, can be burned directly to use, see the program to find the corresp
三路互补pwm
- 三路互补输出,stm32f407三路互补输出(Three way complementary output,stm32f407)