搜索资源列表
VerilogHDL_StepperMotor_control
- 采用Verilog HDL语言编写的步进电机位置系统,实现步进电机的定速、加速、减速、定位,且速率和加减速度都能做到连续可调的程序,对控制类相关的学习者价值很高
motor.无级变速步进电机程序
- 无级变速步进电机程序是一个AVR单片机驱动步进电机正反转的程序,并且有加减速度功能,Variable speed stepper motor program is an AVR microcontroller to drive a stepper motor is reversing the process, and has the speed function of addition and subtraction
motor-s
- 步进电机加减速计算 说明输入步进电机的加减脉冲步数,就可计算出电机加减速的静态表(16进制输出)-motor s type download
xinde
- 89C51单片机控制步进电机,实现正反转,加减速和复位,用位数码管显示转速状态和级别-89C51 microcontroller stepper motor to achieve reversing, acceleration and deceleration, and reset, with digital display speed status and level
200309221430480375
- 本文主要介绍了基于MSP430F149单片机实现的步进电机通用控制器。该控制器可同时控制多台步进电机按曲线方式运行,包括加减速、定位及换向功能等。文中重点探讨了步进电机升降速曲线的设计方案及其实现方法。 -In this paper, based on the MSP430F149 single-chip stepper motor to achieve universal controller. The controller can simultaneously control multipl
motor
- 双轴步进电机同步动作,以XY坐标为目的地,同时具备自动加减速。-motor XY run, and add speed
drvtest2
- 步进电机控制程,加减速控制。行走步数控制-Stepper motor control process, acceleration and deceleration control. Control of walking a few steps
xiaqunfeng
- 题目:用按键控制步进电机 功能实现: K1控制步进电机的开关 K2控制转向 K3速度加;K4速度减 按下开始或速度调节时会动态显示进度条 器件:Atmega88学习板,NOKIA5110液晶,28BY-J48(四相八拍步进电机) 日期:2010.07.25-Title: The function keys control the stepper motor to achieve: K1 K2 switches control the stepper motor
main
- 用51单片机驱动四相六线步进电机,电机正反转,加减速-step motor
motor_angle
- 步进电机的控制程序,有四个键来控制:调零键,加角度键,减角度键,运行键。通加减角度达到需要的角度,按运行即可转到需要的角度。单片机是stc89c52-Stepper motor control program, there are four keys to control: zero key, plus the angle button, reducing the angle button, run key. Achieve the required angle through the angl
bjdjdanpianji
- 单片机控制步进电机加减速C语言源程序,通过不断改变定时器的定时初值来提高频率。-Single-chip stepper motor control acceleration and deceleration C language source program
89c51-stepper-motor-drive-design
- 89c51步进电机的驱动设计.设计要求. 开机后,电机不转,按下启动键,电机旋转,速度为25 r/min,按下加1键速度增加,按下减1键,速度降低,最高速度为100 r/min,最低转速为25 r/min,按下停止键,电机停转。速度值要求在数码管上显示出来。 -89c51 stepper motor drive design. Design requirements. Turned on, the motor does not turn, press the start button,
code
- 这是关于AVR步进电机的控制程序,能够实现步进电机加减速度以及速度的控制。-This is on the AVR stepper motor control procedures, can realize the stepper motor acceleration and deceleration and speed control.
motor
- 步进电机的加减速处理,能够实现单独加减功能-The acceleration and deceleration of the stepper motor processing, separate subtraction
motor
- 步进电机驱动,32等级速度,带加减速度控制。verilog编写。-step motor driver,32 level speed.
3
- 实现步进电机的加减档,51单片机例程,达到变速的目的-Addition and subtraction stepper motor stalls, 51 microcontroller routine, to achieve the purpose of variable speed
STM32-PWM
- 基于KEIL4.7开发软件的在STM32F103ZET6单片机上实现PWM波产生的源代码,功能为定义两路IO口(可多路)产生占空比为50 —75 的PWM信号,两路信号通过四个按键进行加和减的变化,实现对直流或步进电机的调速控制,示波器波形稳定,同时可实现电机正反转控制-KEIL4.7 based software development to achieve PWM wave generated source code on STM32F103ZET6 microcontroller func
JIJIANSU
- 单片机控制步进电机加减速,包括加减速度C程序和HEX文件,可以直接下载到单片机-Single-chip stepper motor control acceleration and deceleration, including the deceleration C program and HEX files can be downloaded directly to the microcontroller