搜索资源列表
ADC0809
- ADC0809 VHDL控制程序，代码很详细，已经调试通过-ADC0809 VHDL control program, the code is very detailed, have been debuged
-AT89S51-with-ADC0809-
- AT89S51单片机与ADC0809模数转换器的三种典型连接-Three typical microcontroller AT89S51 with ADC0809 ADC connection
adc0809
- adc0809是电压的模数转换芯片，用单片机驱动，次程序就是正确的驱动程序。但是精度要自己调试。-adc0809 voltage analog-digital converter chip, single-chip driver, sub-program is the correct driver. However, the accuracy to debug yourself.
adc0809
- ADC0809转换器的verilog版本,运用在ISE上，直接可用（注意没有考虑频道问题），结果显示在数码管里（十进制）-Verilog version ADC0809 converters, used in the ISE, directly available (note does not consider channel problems), the results are displayed in the digital tube (decimal)
cai-yang-dian-lu-shi-xian-ADC0809
- 用状态机对ADC0809的采样控制电路的实现的源代码，用maxplus软件运行，管脚已配置完成，芯片为EP1K30TC144-3-State machine to achieve ADC0809 sampling control circuit of the source code, run the software with maxplus Pin has been configured, the chip is EP1K30TC144-3
ADC0809-VHDL-control-procedures
- ADC0809 VHDL控制程序源代码及仿真结果-ADC0809 VHDL source code of a program to control the simulation results
ADC0809
- 这是一份关于ADC0809的资料，里面有本人亲自写的程序，并有调试过程，适用于初学者。-This is about a ADC0809, which has personally written procedures, and debugging process for beginners.
MCS51-ADC0809
- 自己做的一个用ADC0809实现的ad转换，通过试验验证-done with a realization of the ad Connection between ADC 0809 conversion, the experimental results
adc0809
- 与89c51单片机与ADC0809转换程序-With 89c51 microcontroller with ADC0809 conversion process
ADC0809
- 次VHDL代码实现FPGA与ADC0809的通信，通过ADC0809的模数转换功能转换为数字信号进入FPGA处理-Times FPGA VHDL code to communicate with the ADC0809, ADC0809 analog-to-digital conversion by function into the digital signal processing into the FPGA
stc89c52--MQ2--ADC0809
- stc89c52单片机，实现的MQ2烟雾传感器报警，把烟雾传感器模拟量通过ADC0809转成数字量，通过1602液晶显示-stc89c52 microcontroller to achieve the MQ2 smoke sensor alarm, the smoke sensor through ADC0809 analog into digital quantity by 1602 LCD
ADC0809
- 51 单片机 ，ADC0809，验证运行通过-51 single, ADC0809, verification run through
ADC0809
- 基于51单片机的ADC0809驱动程序，自己写的，经实践检验证实可用。-Based on 51 MCU ADC0809 driver, write your own, proven by the test of practice available.
adc0809
- 编程实现adc0809模数转换过程,内容详细，附有详细说明-programming adc0809 analog to digital conversion process
ADC0809
- 使用adc0809和51单片机制作数字电压表-Produced using adc0809 and 51 digital voltmeter
ADC0809
- 用ADC0809进行数据实时采集，并用PROTUES仿真实现，经过调试功能完整。-ADC0809 voltage measuring
adc0809
- 1、用状态机设计A/D转换器ADC0809的采样控制电路，并在数码管上显示转换结果； 2、设置有复位和启动/保持开关，要求 ⑴ 复位开关用来使A/D转换器复位，并做好A/D转换准备； ⑵ 启动/保持开关用来控制A/D转换器开始连续转换或停止转换保持结果，即按一下启动/保持开关，启动A/D转换器开始转换，再按一下启/停开关，停止转换并保持结果。 3、采用Verilog HDL语言设计符合上述功能要求的控制电路。-1, with the state machine design A/
adc0809
- 运用ADC0809和51芯片制作的数字电压表，在proteus的基础上进行的仿真，能够实现0-5V内的AD转换进行数码管显示，其误差不超过0.002V。-Using ADC0809 and 51 chip digital voltmeter, on the basis of proteus simulation, to implement the AD conversion within 0 to 5 V digital tube display, the error is less than
ADC0809-VHDL
- 这是一段基于VHDL语言，实现对ADC0809的简单控制的程序-This is a VHDL-based language, to achieve a simple control program ADC0809
ADC0809
- 这是adc0809转换用的c语言程序文件，用于模数转换- adc0809 Conversion of c language program file