搜索资源列表
CY7C68013A
- CY7C68013说明书及开发实例。安装程序，驱动程序和下载程序-CY7C68013 manual and development examples. Install programs, drivers, and download the program
USB_Control_Firmware
- C++语言编写的针对CY7C68013A芯片的固件程序。包括了对USB Slave FIFO的配置和内部传输管道以及FIFO大小的必要控制。该程序在硬件上通过测试，在没有其他USB设备干扰的应用下，可以确保450Mbps通讯效率。-Firmware control for USB Slave FIFO in CY7C68013A. It define the necessary configuration on transaction segment and pipe as well as FI
USB_UP_Monitor
- 基于USB芯片CY7C68013A的上位机C++程序。该程序结合相应的CY7C68013固件程序配合使用可以完成PC/Laptop与其他硬件设备通过USB协议完成数据通讯。该程序已经编译并成功在硬件平台上完成数据采集的测试。-The C++ project for USB UP-Monitor function based on CY7C68013 chip. It has been proven in hardware platform and realize the correct USB
usbtolpt6
- 基于CY7C68013A的usb转标准并口的源代码 -Source code based CY7C68013A usb to standard parallel port
Manual-Mode
- cypress s cy7c68013a code,config gpif,it is manual mode,include master and slave code.
onlyone
- 本程序是与CY7C68013A从模式固件程序配套的上位机程序，可以用于读写usb设备上的数据。-This program is supporting the PC program with CY7C68013A mode firmware, can be used to read and write data on usb device.
Read-PortE
- 本程序包括上位机和下位机程序，上位机用来通过usb来读取CY7C68013A引脚的电平。-This program includes a host computer and lower computer program, CY7C68013A pin level used to be to read through the usb host computer.
slave-fifo
- 本程序主要用于开发usb数据传输时的CY7C68013A固件程序，采取的是从模式的数据传输，只要把程序直接下载到EZ-USB中，然后再去写设备端程序就可以了。-This procedure is mainly used for the the CY7C68013A firmware development usb data transmission, taken from the mode of data transmission, and, as long as the program is
USB-PHY
- CY7C68013A的开发文档,usb 2.0,usb外设控制器-CY7C68013A datasheet
Cy7C68013-slavefifo-design.rar
- 使用Cypress的Cy7C68013A芯片进行设计，实现Slave FIFO模式的数据采集。程序包括USB固件程序以及主机程序。,Using Cypress' s Cy7C68013A chip design, data acquisition Slave FIFO mode. The program includes a USB firmware and host program.
hid-mouse
- 基于CY7C68013A的USB鼠标开发-CY7C68013A-based the the USB mouse of development of
Fx2fw-sdcc
- The code in this directory is for Cypress FX2 (e.g. CY7C68013A) and can be compiled with the SDCC compiler (I tried version 2.6 as shipped with Ubuntu 6.10). Once I had a version that could be compiled with Keil tools (until early 2007), bu
Read-PortE
- CY7C68013A，EZ-USB 读portE 实例-EZ-USB Read portE instance
13
- 使用Cypress的Cy7C68013A芯片进行设计，控制外部LED数码管的显示。程序包括USB固件程序以及主机程序-Cypress' s Cy7C68013A chip design, control external LED digital tube display. The program includes a USB firmware and host program
14
- 使用Cypress的Cy7C68013A芯片进行设计，通过外接EEPROM来进行上电时的重列举。程序包括USB固件程序以及主机程序-Cypress' s Cy7C68013A chip design, re-listed through an external EEPROM on power. The program includes a USB firmware and host program
USB-to-USB-software3
- CY7C68013A芯片USB程序源代码，可以实现USB转IDE硬盘，USB转SATA硬盘接口数据传输-The CY7C68013A chip USB source code, can be achieved USB-IDE hard disk, USB to SATA hard disk interface data transfer
the-usbee-logic-analyzer-program
- usbee逻辑分析仪程序 上位机程序 CY7C68013A烧写固件 Logic SDK Users Guide-usbee logic analyzer program host computer program the CY7C68013A programming firmware Logic SDK Users Guide
FA161-SCH
- 联华众科FPGA开发板FA161核心器件为 Altera Cyclone系列FPGA EP1C6，FA161板载有SDRAM，SRAM，FLASH方便制作各种应用，开发板所带资料中包括了上位机与开发板USB通信，上位机与开发板以太网通信，上位机与开发板串口通信例程。FA161板载有USB 1.1，USB 2.0(CY7C68013A)接口，以太网接口(RTL8019AS)。FA161上可以进行HDL程序开发，可以进行nios ii程序开发，可以结合MATLAB制作DSP Builder应用。FA
CY7C68013A-Slave-FIFO-read
- 实现CY7C68013 slave FIFO与计算机通信的固件程序-failed to translate
AsyFIFO
- cy7c68013a芯片的slaveFIFO传输例程，利用异步传输可以实现数据读写，包含芯片固件代码和fpga发送数据的代码。