搜索资源列表
MSP430单片机与L298驱动控制单片机正反转直行后退
- MSP430单片机与L298驱动控制单片机正反转直行后退 基于IAR for MSP430F16X
MOTOR.rar
- msp430控制直流电机,L298驱动,具有正反转,pwm调速功能。,msp430 control of DC motor, L298-driven, with positive inversion, pwm speed control function.
DC-Motor
- 基于stm32的L298驱动直流电机调速程序-Based on the L298 stm32 drive DC motor speed control program
L298
- 基于ARM7的L298驱动程序,芯片L298,控制两个直流电机,没有用PWM调速-Based on ARM7-L298 driver chip L298, control two DC motors, there is no speed control with PWM
L298
- L298驱动直流、步进电机,带有PROTUES仿真-L298-driven DC, stepper motors, with PROTUES simulation
pwm
- 利用延时产生pwm信号,通过L298功率放大器驱动直流电机- pwm DC-motor
pwm
- 主要是驱动两个直流电机的程序,通过L298带两个直流电机,稍修改程序即可运用于步进电机。-Drive two DC motors are mainly the procedure, through the L298 with two DC motors, slightly modify the program can be used in stepper motors.
PWMControlMOTOR
- 多功能小车仿真。L298驱动直流电机,有液晶LCD显示方向,速度。-Multi-function car simulation. L298-driven DC motor,there is the direction of liquid crystal LCD display,speed.
DC-motorvelocitymodulation
- 直流电机调速实验C语言程序,使用L298N驱动-DC Motor Speed Experiment C language program, use the L298N drivers
pwm
- 直流电机驱动芯片采用L298.支流电机驱动就是利用PWM脉宽控制L298电流输出大小,从而达到控制电机的目的-Motor Driver IC using L298. Tributaries is the use of motor-driven PWM pulse width control L298 current output size, so as to achieve the purpose of the electrical control-DC motor driver chip L2
1
- 这是一个使用51单片机加上L298驱动直流电机的程序源代码。-This is a single chip using 51 L298-driven DC motor with source code.
DC-motor-driver-program-of-L298
- L298驱动直流电机程序,其中包括正反转-L298 DC Motor Driver Program
motor02
- 自己写的电机控制第二个:VB做的上位机通过串口向51单片机发送命定,通过L298驱动直流电机,电机反溃的信息又发回VB到VB上显示-To write the second motor control: VB to do the PC via the serial port to send commands to the microcontroller 51 set by L298 drive DC motor anti-ulcer information and send back to VB
zhiliudianji
- 运用L298驱动直流电机,代码中包含有正转、反转、停止等程序。-DC motor driver using L298, the code contains a forward, reverse, stop and other procedures.
L298
- L298控制直流电机,C语言驱动,可直接用于凌阳单片机,亦可改动接口后用于其他单片机-L298 controlled DC motor, C language driver, can be used directly Sunplus can also be used for other changes to the interface chip after
l298
- AT89S52单片机,L298驱动直流电机C51程序-l298-driven DC motor
simulate
- 压控阀控制系统,L298驱动直流电机,控制阀门开关,proteus 仿真,LED显示电机转数,-Voltage-controlled valve control system, the L298 to drive DC motor, control valve switch, proteus simulation, LED display motor revolutions.
PWM电机 - 副本
- 驱动直流电机,通过l298n来驱动,stm32板拉高引脚PA9与PA10,同时PA7输出PWM值(The drive DC motor is driven by L298N, the STM32 board pulls the high pin PA9 and the PA10, and the PA7 outputs the PWM value)
驱动
- 驱动直流电机工作,很多专门的电机驱动ic,如L298,33886等,其内部主要还是采用的H桥电路,用起来比较方便。同时也有可用分离元件来设计H桥驱动电路,其驱动能力强。(Drive the work of DC motor)
直流电机速度PID控制
- 光电编码器测得的电机速度反馈信号反馈到单片机中。电机设定速度由ZLG7289模块获得,通过SPI通信传输给单片机。单片机系统根据给定的转速与反馈回来的实际速度相减得出偏差,经过控制算法得出控制量。单片机再把控制量以PWM的形式输出,经过L298功率放大驱动直流电机。ZLG7289模块主要用于显示当前直流电机实际转速和给定转速,并让用户通过键盘输入设定速度。(The motor speed feedback signal measured by the photoelectric encoder