搜索资源列表
uart from opencores
- 用VHDL实现串口 可以实现与pc机的通信 收发 中断都可以 效果比较好-VHDL implement serial port, it can communicate with pc, it can accept and send message, and it can be interrupted.
FPGA-UART
- 用FPGA器件实现UART核心功能的一种方法 串行外设都会用到RS232-C异步串行接口,传统上采用专用的集成电路即UART实现,如TI、EXAR、EPIC的550、452等系列,但是我们一般不需要使用完整的UART的功能,而且对于多串口的设备或需要加密通讯的场合使用UART也不是最合适的。如果设计上用到了FPGA/CPLD器件,那么就可以将所需要的UART功能集成到FPGA内部,本人最近在用XILINX的XCS30做一个设计的时候,就使用VHDL将UADT的核心功能集成了,从而使整个设计更
uart.rar
- 实现串并口通信,共有发送和接受两个模块。,Strings parallel to achieve communication, send and receive a total of two modules.
uart.rar
- 基于vhdl的串口通信模块,即异步收发机,可实现单片机核fpga的收发串口通信,遵从rs232协议,已经调试过,很不错的资源,Vhdl-based serial communication module, that is, asynchronous transceiver can achieve single-chip transceiver nuclear fpga serial communication, rs232 to comply with the agreement, has be
71477212NiosII_uart
- 串口sopc uart实现串口功能,包含帧的开始字节,命令字节-Serial sopc uart serial implementation features, including frame start byte, command byte
uart_vhdl
- VHDL语言的实现标准的UART串口,并可以多次例化成多串口的-The realization of VHDL language standard UART serial port
uart
- 用VHDL编程,在FPGA上实现串口的控制!希望一切分享一下!-Using VHDL programming, the FPGA, Serial control! Hope that all share!
UART
- VHDL语言写的串口发送、接收程序,根据晶振和相应的波特率修改分频器就可以实现!-Written in VHDL serial send, receive, process, according to crystal and the corresponding baud rate divider changes can be achieved!
UART
- 用VHDL实现与电脑串口进行通信。已通过开发板验证正确。开发板时钟50M,波特率19200.-VHDL implementation using serial communication with the computer. Has been verified through the development board are correct.
FPGA_UART
- 用Verilog语言实现的FPGA UART独立收发模块 思路简单,代码简洁。在Lattice LFE3EA VERSA开发板上验证通过,编译器Lattice Diamond. 功能:串口收到数据后立即回传,此后每一秒串口数据+1再发送。-Using Verilog language independent of FPGA UART transceiver idea is simple, concise code. Development board in Lattice LFE3EA
topone
- 基于火龙刀开发板的FPGA和PC的UART串口通信的VHDL实现,支持LCD实现分页显示和LED 数码管显示。-FPGA and PC UART communication module implemented by VHDL, running on Dragon platform, with support of LCD and LED display.
uart_rx
- 用VHDL语言实现的Uart串口通信程序。在xilinx公司FPGA芯片验证过。-Uart serial communication program using VHDL. Validation in xilinx Company FPGA chip.
UART
- 基于FPGA的串口程序 由VHDL语言编写,通过串口助手实现数据的发送与接收-FPGA-based serial procedures by VHDL language and sending and receiving data through the serial port assistant
UART_VHDLCodes
- 基于VHDL的异步串口收发器,在FPGA上设计Uart接收模块实现从pc接收串口数据; 在FPGA上设计Uart发送模块,把从pc接收的数据的16进制值加1再发送给PC; 设计单片机和FPGA接口模块,把接收到的数据送给单片机,并显示在LCD上 -VHDL-based asynchronous serial transceivers Uart receive module in the FPGA design from pc to receive serial data desig
FPGA_UART
- FPGA实现UART串口通信协议 采用VHDL语言,顶层文件采用原理图的方式,简洁直观-FPGA Implementation of UART serial communication protocol
UART
- 使用标准VHDL编写的RS232协议,可在CPLD或者FPGA上直接实现串口通信功能。-use VHDL to implement RS232 protocol, which can be used in CPLD or FPGA
vhdl_source
- VHDL语言实现UART 串口功能;波特率可以自由设置。-VHDL language UART serial port function,The baud rate can be freely set.
uart
- VHDL实现串口转换的代码,串行通信的发送器有五个状态:--1.X_IDLE(空闲)状态 : 当UART被复位后,状态机将立刻进入这一状态,在这个状态下, -- 状态机一直等待发送命令XMIT_CMD,当接收到发送命令后,状态机进入X_START状态,准备发送起始位信号 --2.X_START状态 : 在这个状态下,UART发送一个位时间宽度的逻辑'0',信号至TXD,即 -- 起始位,紧接着状态机进入X_SHIFT状态,发一位数据 --3.X_WAIT状态 : 当状态机处于这一个状态时
uart
- RS232通信程序,用于实现PC端与FPGA之间实现串口通信(RS232 communication program for realizing serial port communication between PC and FPGA)
vhdl的串口UART编写
- 该资料是用vhdl语言实现串口UART的编写,程序包括发送模块,接收模块,波特率发生模块和顶层模块。程序无BUG,可以直接使用