搜索资源列表
EedffazipD
- EDFA的掺铒光纤长度模拟计算,附3篇相关论文,330mw的980nm泵泵浦,3db的泵浦吸收,12m最佳长度已经的到验证,可作为EDFA设计参考 -EDFA erbium-doped fiber length simulation of three related papers, 330mw of 980nm pump pump pump 3db absorption 12m optimum length has been to verify, can be used as the EDF
edfa-gain-with-length
- erbium dopped fiber amplifier with length
Dynamic_EDFA
- 掺饵光纤放大器EDFA动态仿真,掺饵光纤放大器EDFA动态仿真-Dynamic EDFA simulation,Dynamic EDFA simulation
edfa
- matlab code for siminar doc
edfa
- 掺铒波导放大器增益计算matlab源程序-Erbium doped waveguide amplifier gain calculation matlab source
eda_8
- edfa edfrnrt utnuh u h u yhu ub(unènn unu(nu(-edfa edfrnrt utnuh u h u yhu ub(unènn unu(nu(
FiberLaserAmplifierToolbox
- To get a phenomenological understanding of how an EDFA works, we need to look at the energy-level structure of erbium.
EDFA1
- program to simulate EDFA
fiber
- 掺铒光纤放大器数值计算 求解激光速率方程的数值解 -EDFA Numerical calculation
Final_Report_IEEE_PAPER
- The project describes the wavelength Division Multiplexing using EDFA amplifer. The tools used for this project are optisystem and matlab.
oes_oas
- 常用的掺铒光纤中的吸收和辐射截面参数,对于模拟EDFA的同人可能需要。-Commonly used erbium-doped fiber in the absorption and radiation cross-section parameters, for the simulation EDFA colleagues may need.
EDFA-980nm
- 模拟单模光纤中的掺铒光纤的放大,泵浦源为980nm。使用了RK算法计算的。-Simulation of single-mode fiber in the erbium-doped fiber amplification, the pump source is 980nm. Using the RK algorithm.
RADMQN
- EDFA的掺铒光纤长度模拟计算,附3篇相关论文,330mw的980nm泵浦,3db的泵浦吸收,12m最佳长度已经得到验证,()
reyvrence
- EDFA的掺铒光纤长度模拟计算,附3篇相关论文,330mw的980nm泵浦,3db的泵浦吸收,12m最佳长度已经得到验证,()
biber
- EDFA的掺铒光纤长度模拟计算,附3篇相关论文,330mw的980nm泵浦,3db的泵浦吸收,12m最佳长度已经得到验证,(The simulation calculation of the length of erbium-doped fiber in EDFA, with three related papers, the 980nm pump of 330mw, the pump absorption of 3db, the optimum length of 12m have been
基于optisystem的长距离光纤传输系统设计
- 设计一个4×2.5Gbit/s 长距离光纤传输系统,并利用OptiSystem 仿真验证。 1.采用波分复用技术,波长设置以100GHz 为间隔,频率分别为193.1THz、193.2THz、193.3THz、193.4THz,每个波长传输速率为2.5Gbit/s(NRZ),传输距离为300km。采用常规光纤,光纤损耗系数为0.25dB/km。 2.单通道光发送机最大输出功率为0dBm,光接收机的接收光功率不低于-26dBm,过载点为-10dBm。 3.可以采用EDFA 作为线路放大器,其
基于optisystem的光纤仿真实例
- 一些关于光纤通信系统的仿真设计,包含: 1-OptiSystem的基本操作 2-基本光纤通信系统设计 3-WDM系统设计 4-长距离光纤传输系统设计 5-EDFA设计 6-内调制光纤链路设计
Optiwave_OptiSystem
- 一款不错的仿真软件!OptiSystem是针对于科研工程师、光通信工程师、系统集成商、学生和各种各样的其他用户的需要应运而生。不断进化的光通讯市场呼唤一款功能强大且易于使用的光通信系统设计软件,OptiSystem正好满足了这一需求。 OptiSystem 能够使用户对如下应用进行规划、测试和仿真(在时域和频域同时进行):光网络设计,包括OTDM、SONET/ SDH环、CWDM、 DWDM、 PON、线缆、OCDMA单模和多模传输系统,自由空间光学FSO、ROF、OFDM(直接检波,相干检波