搜索资源列表
(Artech)AdvancedTechniquesRFPowerAmplifierDesign.r
- 关于RF放大器的设计的文挡资料，对从事手机射频的同学很有帮助-on RF amplifier design of the text block, right in the handset RF students helpful
rfamp
- RF amplifier matlab-simulink files. Requires RF toolbox to run.
DPD_sim
- Digital Predistortion of Nonlieaner RF Power Amplifier with Memory Effects. This M code simulates a DPD technique linearization for a AB-class nonlinear HPA with memory effects. Here we consider a memory polynomial predistorter to modeling nonline
Impedancematchingandsmith
- 阻抗匹配与史密斯（Smith）圆图 在处理RF系统的实际应用问题时，总会遇到一些非常困难的工作，对各部分级联电路的不同阻抗进行匹配就是其中之一。一般情况下，需要进行匹配的电路包括天线与低噪声放大器（LNA）之间的匹配、功率放大器输出（RFOUT）与天线之间的匹配、LNA/VCO输出与混频器输入之间的匹配。匹配的目的是为了保证信号或能量有效地从“信号源”传送到“负载”。-Impedance matching and Smith (Smith) Smith chart in dealing wi
CMOSshepindizaoshengsheji
- CMOS射频低噪声放大器的最详细的设计，相信熟读后，定会对运放电路类有一个很好的了解。-CMOS RF low-noise amplifier of the most detailed design, I believe familiar, the setting op-amp circuit class will have a good understanding.
GF
- 射频功放原理图,protel99se打开-RF power amplifier schematic, protel99se open. . . . . . . . . . . .
POWER_AMPLIFIER_DESIGN_FUNDAMENTALS
- POWER AMPLIFIER DESIGN FUNDAMENTALS 1-Main characteristics (two-port networks, gain, delivered power ) 2-Gain and stability 3-Stabilization circuit technique 4-Class-A,-B,-C operation modes 5-Linearity 6-DC biasing 7-Push-pull amplifie
RF_AND_MICROWAVE_POWER_AMPLIFIER_DESIGN
- RF AND MICROWAVE POWER AMPLIFIER DESIGN NONLINEAR ACTIVE DEVICE MODELING Power MOSFETs GaAs MESFETs and HEMTs BJTs and HBTs-RF AND MICROWAVE POWER AMPLIFIER DESIGN NONLINEAR ACTIVE DEVICE MODELING Power MOSFETs GaAs MESFETs and HEM
HighEfficiencyPowerAmplifiserDESIGN
- HIGH-EFFICIENCY POWER AMPLIFIER DESIGN 1-Overdriven Class B 2-Class F circuit design 3-Inverse Class F 4-Class E with shunt capacitance 5-Class E with parallel circuit 6-Class E with transmission lines 7-Broadband Class E circuit design
RS9110N1122EVB
- The RS9110-N-11-21 module from Redpine s Connect-io-n™ family of products is a complete IEEE 802.11bgn Wi-Fi client device with a standard seria or SPI interface to a host processor or data source. It integrates a MAC, Baseband p
attachments_2011_01_20
- OFDM modulation produces higher Peak Average Power Ratio (PAPR) whenever the carriers in OFDM symbol add synchronously in the time domain resulting in higher signal power. This high power saturates the power amplifier placed in the RF section res
RFPA-Based-on-Volterra
- 主要运用Voherra级数理论分析射频功放(RFPA)器件工作在弱非线性条件下信号失真特性。介绍了V01． terra级数在非线性建模中的应用，推导了非线性传递函数的公式。在Advanced Design System 2006A软件的仿真环 境下对射频功率放大器进行仿真，利用计算机仿真实现了在弱非线性条件下对任意频率输入时功率放大器的输出 频谱估计。-The main use of Voherra series theory analysis of RF power amplifi
fmpreamp
- High performance RF amplifier for the FM band which can be successfully built without any special test equipment.Preamplificador FM.
Power_Amplifier_Application_Note
- design RF amplifier using ADS sofware
rf-amplifier-300w-fm-88-108-mhz-sch2
- 300W RF Amplifier using PT9383
Presentation_on_RF_Predistortion_of_Power_Amplifie
- 利用ADS设计功放（PA），提供了一些设计步骤以及理论，同时利用ADS设计RF预失真，来提高功放的线性度-Design using ADS amplifier (PA), provides some design procedure and theory, while taking advantage of ADS design RF Predistortion, to improve the linearity power amplifier
TAT7467H
- Triquint射频差分放大器,可用于CATV频段,末级PA, 16.5db放大-The TAT7467 is a 75 Ohm true differential RF Amplifier covering medium power applications in the CATV band. The TAT7467 includes on-chip linearization to improve 3rd order distortion performance while mainta
rf-amplifier-design
- 本系统由前级宽带放大模块、增益控制模块、无源衰减模块、功率放大模块和直流稳压电源模块组成，具有0~60dB范围内手动连续调节、带宽为0.3M~100MHz的功能。在前级放大中，采用两片宽带低噪声放大芯片ADA4895级联对输入信号进行放大，然后由800MHz带宽的可变增益放大器AD8368进行放大倍数调节，最后通过低噪声电流反馈运放THS3001进行功率放大，从而达到1V有效值输出。在系统设计中，采用了合理的阻抗匹配，规范的高频线路布局和有效的散热设置，并且综合考虑了去耦、滤波，以及使用同轴电缆
300W-FM-RF-Amplifier-Circuit
- 300w rf transmitter power amp
High-Power-RF-Amplifier-0.2Mhz-to-10Mhz
- High Power RF Amplifier 0.2Mhz to 10Mhz using MRF 151G