搜索资源列表
S3C2440---code
- KEIL MDK环境下的TQ2440裸奔程序，之前在网上找了几个，但是nandflash操作不能使用，我改了一下，烧上去可以直接用，用串口打印运行结果。-KEIL MDK environment TQ2440 streaking procedure, before the Internet to find a few, but nandflash operation can not use, I changed a bit, burning up can be used directly wit
sy10
- 本实验将实现如下功能：本实验利用TIM5_CH1来做输入捕获，我们将捕获PA0上的高电平脉宽，并将脉宽时间通过串口打印出来，大家可以通过按WK_UP按键，模拟输入高电平。同时，本实验将保留上一个实验的PWM输出，DS0还是会由暗-->亮的循环变化，大家可以通过杜邦线连接PA0和PB5，来观测PWM输出的高电平时间。-The experiment will achieve the following functions: In this study, TIM5_CH1 do input ca
STM32F407-led
- STM32 usar程序，改程序实现LED流水闪烁，和串口打印功能-STM32 usar program, change the program to achieve LED water flashes, and serial print function
ow_18b20-(2)
- stm32用18b20读出温度并使用串口打印显示-stm32 18b20 temperature readout with a serial printer
F00x_UART0_STDIO
- c8051F00串口驱动程序,实现串口打印-c8051F00 serial driver, serial print
serialprint
- 串口打印机,在wince上实现串口打印功能-serial pirinter
uartdayin
- msp430f5529串口打印程序，实现字符串的发送，用于gsm等。-//****************************************************************************** // MSP430F552x Demo- USCI_A0, 9600 UART, SMCLK, LPM0, Echo with over-sampling // // Descr iption: Echo a received character,
ADC-DMA
- ADC+DMA调试通过 可进行数据采集，并通过串口打印-ADC+DMA debugging through data can be collected and printed through the serial port
STM32-IIC--MMA8451
- STM32的控制MMA8451三轴加速度芯片的IIC驱动，串口打印数据到电脑显示！-STM32 control MMA8451 the triaxial acceleration chip IIC driver, serial print data to a computer display!
STM32--SD-RW
- 开机先初始化SD卡，如果SD卡初始化完成，则读取扇区0的数据，然后通过串口打印-Boot initializes the SD card, if the SD card initialization is complete, the read sector 0 of the data, and then print through the serial port
IRQ_
- S3C2440 裸机中断程序，当有按键中断时，利用函数uart_printf() 向串口打印一些信息，同时led灯显示-S3C2440 bare interrupt program, when a button is interrupted, using the function uart_printf () print some information to the serial port, and led lights display. .
GPS
- norflash运行，串口打印GPS数据-norflash run, serial print GPS data
nandflash_demo
- 该实验程序完成了land flash的读写测试，包括串口打印输出功能，适用于fl2440，ok2440上的k9f**（2K） nand falsh读写实验代码-The experimental procedure is completed the land flash read and write tests, including serial print output for fl2440, ok2440 on k9f** (2K) nand falsh experimental code r
MMC_SD
- 本实验将实现如下功能：开机的时候先初始化SD卡，如果SD卡初始化完成，则读取扇区0的数据，然后通过串口打印到电脑上。如果没初始化通过，则在LCD上提示初始化失败。 同样用DS0来指示程序正在运行。-The experiment will achieve the following functions: boot time to initialize the SD card, if the SD card initialization is complete, the data is read s
USBReadDir
- USB主控制芯片CH375，读取U盘根目录信息，通过串口打印出来，希望对使用CH375的朋友有帮助-USB host controller chip CH375, read U root directory information through the serial print it out, I hope to help a friend with CH375
GPS_LEA6H_NMEA_protocol
- 用STM32接收GPS信号，设备采用NMEA协议，接收后将ASCII码转换成数值，同时分解协议内容，并通过串口打印到上位机上-With STM32 GPS signal reception equipment using NMEA protocol, the receiver will convert the ASCII code value, while decomposition agreement, and print to the PC through the serial port o
test9_AD
- CC2530芯片内部温度采集，并使用串口打印输出，可以实时观察芯片温度变化-CC2530 chip temperature acquisition and use serial printer output, temperature changes can be observed in real time chip
tiny6410_key_int_uart
- 开发环境为RVDS4.0，基于开发板Tiny6410，裸机程序，该程序涉及内容按键、中断、串口打印。 按键通过外部中断方式来控制，且串口打印按键信息；当按下K1，串口打印：Key1 is push down!，然后四个用户led显示为流水灯；当按下K2，串口打印：ey2 is push down!，然后led全灭；当按下K3，串口打印：Key3 is push down!，然后led全；当按下K4，串口打印：Key4 is push down!，然后beep响一声；-Development en
tiny6410_uart
- 开发环境为RVDS4.0，基于开发板Tiny6410，该程序为裸机控制程序，实现串口打印，实现方式：程序下载后打印串口信息； 显示为：a hello Uart-Development environment for RVDS4.0, based development board Tiny6410, the program for the bare metal control procedures to achieve serial printing, implementation: Aft
stm32TFTLCD
- STM32 开发板上的 LCD 接口， 来点亮 TFTLCD，并实现 ASCII 字符和彩色的显示等功能，并在串口打印 LCD 控制器 ID，同 时在 LCD 上面显示。-STM32 development board LCD interface, To light TFTLCD, and to achieve the ASCII character and color display capabilities, and print serial LCD controller ID,