搜索资源列表
batterycharge
- 通过单片机程序控制对电池分时充电，并通过热敏电阻实时测温，防止电池充电过程过度发热-MCU programmed by time-charging the battery and, through the thermistor temperature measurement, battery charging process to prevent over-heating
xudianchikuaisuchongdianxitong
- 单片机快速充电系统的研究，很详细的论述了整个过程的充电系统，欢迎交流-SCM rapid charging system, is discussed in detail the whole process of charging system, welcomed the exchange of
RXXA
- 一款7串锂电保护板软件,可实现锂电的充电和放电管理.-A 7 string lithium protection board software enables charging and discharging lithium management.
Powersupplycircuit
- 实用电源电路设计，主要讲解了稳压电源，开关电源，逆变及充电电源的经典电路设计。-Practical power circuit design, the main explanation of the power supply, switching power supply, power inverter and charging circuit design classic.
AD
- /*软件A/D所能实现的精度有限 ， 测量电压范围是2-15V， 而且速度低(约1KHz),但仅用一个电容和一个电阻的诱惑 力，我想大虾您会笑纳的。用于某些场合是有用的。 原理是利用470K电阻对1uF电容充电，利用P0.0口作为检测电压， 当电压低于1/3 VCC时，P0.0读入的I/O电平为0，当充电电压超过 1/3 VCC时，P0.0读入的I/O电平为1。通过测量此过程所用的时间， 就能判断输入电压（需要换算）。 程序的编写用定时器0实现-/* Software
CodeCharger
- 共享我自制的充电器程序，此程序可以控制我的四节电池充电， 内部算法适用于小容量的锂电池充电-I share my home-made charger program, this program can control my four batteries, the internal algorithm is suitable for small-capacity rechargeable lithium battery
595643732051
- 充电程序，充满后转为涓流充电，每月分钟表对电池检测一次。
kuangdeng
- 几年前设计的智能矿灯充电测试系统，包括电路图、印刷电路板图和C程序。-A few years ago designed to test intelligent miner charging system, including schematics, printed circuit board and C program.
12VVRLAcharger
- 程序是关于12V铅酸蓄电池充电器的。充电方式选择的是普通的三段式，PI调节用硬件实现（其实用软件实现比较好，只是毕业在即时间不够了）。程序主要是判断电池的正反接和充电状态，以便实现三段的切换。对充电器有兴趣的朋友可以参考一下（程序写得不是很标准，将就着看吧）。-Program is on the 12V lead-acid battery charger. Charging an ordinary three-stage selection, PI regulator with the hard
LED_charg_290ma
- 用松翰2501写的一个锂电池脉冲充电程序，调节PWM功能-Sonix 2501 with written procedures for pulse charging a lithium battery, adjust the PWM function
openloop1
- 开环充电机仿真图，看了这图你就会做充电机了-Open-loop simulation diagram charger, read this plan you will do a charger
closeloop1
- 闭环充电机仿真图，看了这图你就会做充电机了。-Closed-loop simulation charts charger, read this plan you will do a charger.
controller
- 太阳能电池板控制器，通过感应阳光的不同，控制电池的充电与放电。-Solar panel controller, different from the sun through the induction and control the battery charge and discharge.
spsBattery
- 一种铅酸蓄电池模型 可以充电和放电 可以自己调节充电电压的-a model of battery
Ni-li-battery-charger
- 本程序实现了镍氢电池和锂电池的智能两用充电。采用STC12C5410AD单片机。采用MAX4173-T芯片进行电流采样。-This procedure implements the nickel-metal hydride batteries and lithium batteries intelligent dual-use charge. By STC12C5410AD microcontroller. MAX4173-T chip with current sampling.
wirelessPower
- WPC协议规定的无线充电的基本原理与设计规范，是对无线电力传输爱好者的必备资料-WPC agreement provides for the basic principles of wireless charging and design specifications, is essential for wireless power transmission enthusiasts information
CQC14-46423-2014
- 电动汽车交流充电桩认证规则 是目前所有生产汽车充电桩的厂家获取产品认证所必须掌握的资料
程序
- 铅酸电池充电器 源程序 转灯控制 充电流程不可逆 基于STM8S003F3P6(Lead-acid battery charger source program The rotation lamp controls the charging process based on STM8S003F3P6)
untitled1
- 电动汽车无线充电谐振部分的仿真。。。。。(Simulation of resonant part of wireless charging for electric vehicle)
智能充电系统监控界面
- 利用组态王软件进行电动汽车充电系统的界面设计(Interface design of electric vehicle charging system using Kingview software)