搜索资源列表
func_gen
- 实现一个简易函数信号发生器的功能。系统上电后,默认输出低电平(无波形),默认初始频率为1KHz。波形输出频率可由开发板上的拨码开关SW0~SW3调节,可调范围为1KHz到2KHz,步进量为100Hz。波形由开发板上的DAC_A口输出。共有方波和三角波,正弦波三种波形可供选择,用户只需将开发板上的拨码开关SW6~SW7置成不同取值组合,就可以输出不同波形。其中方波的占空比可以用开发板上的按键开关BTN0~BTN1调节。系统重置按键为开发板上的按键开关BT7。另外,实验验收后我继续加入了锯齿波输出的
Function-signal-generator-
- 用Multisim实现的函数信号发生器,仿真成功,课程设计可以参考利用-Achieved using Multisim function signal generator, successful simulation, curriculum design can refer to the use of
function-of-fangbozhenxianandsanjiao
- 基于FPGA的函数信号发生器VHDL设计,包括方波、三角波和正弦波-FPGA-based VHDL design function signal generator, including a square wave, triangle wave and sine
STM32waveform-settings
- 基于STM32的函数信号发生器的波形设置,包括正弦波、方波、三角波、锯齿波。-STM32-based function generator waveform settings, including sine, square, triangle wave, sawtooth wave.
DDS_8bit_5_7yigai
- DDS函数信号发生,基于fpga的DDS函数信号发生器,已在黑金版上验证。-DDS Function happen fpga-based DDS Function Generator has been verified on the black gold version.
Signal-Generator
- 基于单片机的信号发生器,以单片机AT89S52为控制核心,ICL8038构成的震荡电路为总核心,高精度数字电位器X9C103构成精确调频调幅模块以及可编程键盘和液晶显示器模块构成的的数控及扫频函数信号发生器-Microcontroller-based signal generator, a microcontroller AT89S52 as the control core, ICL8038 oscillator circuit consisting of the total core, hi
hanshuxinhaofashengqi
- 这个是在MSP430上实现的一个函数信号发生器。通过串口uart放送到一个液晶显示器上,显示函数由液晶显示器的库文件提供。-This is implemented on the MSP430 a function signal generator. Run through the serial uart to a liquid crystal display on the LCD display function consists of a library document.
0832
- stc12c5a60s2单片机控制DAC0832作函数信号发生器-stc12c5a60s2 DAC0832 chip control signal generator as a function
project06
- 拿vs写的c#程序,一个函数信号发生器,可以设置调制信号和载波信号,这两种信号可以设置三角波方波和正弦波三种,可以把调制信号和载波相乘,可以截图。可调分量。-Take vs write c# program, a function signal generator, you can set the modulating signal and the carrier signal, the two triangular wave signal can be set to three kinds o
DA
- 用于全国大学生电子设计大赛,一个基于c8051f120的函数信号发生器-For National Undergraduate Electronic Design Contest, a function of the signal generator based on c8051f120
DDS_TLC5620
- DDS函数信号发生器 tlc5620 verilog-dds tlc5620 verilog
Text2
- 基于单片机的DDS信号源设计: 设计一台函数信号发生器,使其能产生正弦波、三角波、方波信号。 1、函数信号发生能产生正弦波、三角波、方波三种周期性波形。 2、输出频率在100hz到6khz 3、可实时显示输出信号的类型、频率 4、输出信号波形无明显失真 -Microcontroller-based DDS signal source design: design a function signal generator, so that it can produc
Impedance-measuring
- 利用NI ELVIS提供的函数信号发生器作为电路的激励信号,在正弦交变信号的作用下,RLC 电路元件在电路中的抗流作用与信号的频率有关。RLC阻抗特性测试实验验证了电阻、感抗、容抗与频率的关系。 -Use NI ELVIS provides signal generator as a function of the excitation signal circuit under sinusoidal alternating signal role, RLC circuit elements
Labview-Data-acquisition-card-
- 基于labview的数据采集系统,包括示波器和函数信号发生器,可以实现简单数据采集.-Labview-based data acquisition system, including oscilloscopes and function signal generator, can achieve a simple data acquisition.
a
- 基于dds的函数信号发生器 程序 -Based dds function signal generator program based dds function signal generator program
STM32waveform-settings
- 基于STM32的函数信号发生器的波形设置,包括正弦波、方波、三角波、锯齿波。-STM32-based function generator waveform settings, including sine, square, triangle wave, sawtooth wave.
generator
- 8051F410实现函数信号发生器(1000HZ)-8051F410 achieve Function Generator (1000HZ)
DDS-signal-generator
- 基于DDS的函数信号发生器,产生正弦波,通过按键控制输出频率-Produce sine function signal generator, based on DDS, through the keys to control the output frequency
wave
- 采用Labview设计一虚拟函数信号发生器, 通过数据采集卡输出波形信号,调节信号的相关参数,可观察示波器上波形的变化情况。-Using Labview to design a virtual function signal generator, through the data acquisition card output waveform signal, adjust the relevant parameters of signal, to observe changes of the
Multiple-function-signal-generator
- 基于quartus ii开发环境下的多种函数信号发生器的设计- Multiple function signal generator quartus ii development environment based design