搜索资源列表
usb
- 关于2410实验板的usb驱动实验与测试代码代码-About 2410 usb driver experimental test board code and test code
kaoqin
- 基于ic卡的考勤系统，mifare1 ic s50，具有很强的开发价值，实验板上跑过，可用，具有参考性-Ic card based attendance system, mifare1 ic s50, has a strong value for development, experimental board ran, available with referential
60
- 60倒计时器C语言源程序 该程序可导入单片机硬件实验板实现59~0的倒计时功能-60 Countdown C language source code of the program can be imported chip hardware test board to achieve 59 to 0 countdown function
keil-ZigBee-cortex_m0
- cortex_M0 实验板的 ZigBee 模块通过 SPI 总线与 LPC11C14 相 连， 数据由 ZigBee 接收后， 先由 ZigBee 传输给 LPC11C14 进行处理， 然后通过 OLED 显示，以及经过串口在串口调试助手中打印-cortex_M0 experiment board ZigBee module is connected via the SPI bus with LPC11C14, after receiving data from the ZigBee,
128x64-LCD-4X8C
- 128X64图形点阵液晶LCD的操作.本实验所需使用的硬件电路为：MSP430F135核心实验板 + LCD4X8C液晶模块-128X64 graphic dot matrix liquid crystal LCD operation
chuankou3
- 模拟电压输入，显示屏显示. 与组态王联机 实验板地址为:15 温度存储地址为15. -Analog voltage input, display with configuration king online test board address is: 15 temperature storage address is 15.
EX4
- 基于可编程器件设计的一个电路，可以实现矩阵键盘的连续输入和数码管的移位显示功能。 1)连续按下按键0~9 、A~E，数字和字母将依次显示在4 位数码管上。 2) 按下F 时，数码管上不显示 F，当前显示的数字按一定频率闪烁。直至按下其他数字和字母后，再次稳定显示4 个数字。以此类推。 3)任何时刻按下实验板上的RST 键，可将电路清零. -Verilog, QuartusII run correctly, can be downloaded to the FPGA. Could
board
- 光通信实验板，实现声光转换，同时带有led液晶显示，扬声器能发出音乐。-Optical communication experiment board, to achieve sound and light conversion, with both led LCD, speakers can send music.
PCserial-communication
- 设计一个与PC串口通信的实验系统，当在PC机上输入十进制数时，可在实验板上显示相应的十六进制数字，而在实验板上按下独立按键A时，在PC机上也可以显示其对应的管脚数56。-Design an experiment with the PC serial communication system, when the PC input decimal number, you can experiment on-board display the corresponding hexadecimal num
bujindianji
- 步进电机的驱动程序，用的是实验板上自带的步进电机，新手座屏-Stepper motor driver, using experimental board comes with stepper motor, novice seat screen
multi-CPU
- Verilog开发的能下载到FPGA实验板上运行的多周期CPU-Verilog can be downloaded to the FPGA development board running experiments multi-cycle CPU
AT89S51design
- 是用DXP来制作单片机实验板，该有的功能都有，学习起来比较方便，还有配套的大程序-DXP is used to produce single-chip board, which has some functions, it was easier to learn, as well as supporting a large program
C8051F340_Ctestprogeramme
- C8051F340 实验板测试程序，非常全面，可以作为初学者或者给予单片机网络开发者的必备资料-C8051F340 experimental board test procedures, very comprehensive and can be given as a beginner or a single-chip network development are essential information
FM-transceiver-experiment
- FM收发实验，包含整个工程的源码，编译可以通过，在实验板上已验证。-FM transceiver experiment, the experiment verified the board.
AD1
- MSP430F149 ADC例程 附带实验板完整电路图-MSP430F149 ADC routine experiments with complete circuit board
num_clock
- 基于DE0实验板开发的verilog数字钟程序。实现了12/24小时制切换；闹钟；整点报时等功能。-Based on experimental board development DE0 verilog digital clock procedures. To achieve a 12/24 hour switch alarm clock whole point timekeeping function.
CH451
- 在m2t1实验板上，利用CH451的键盘显示功能控制数码管的显示实现跑马灯模式、闪烁模式 C语言-In m2t1 experimental board, using the keyboard display CH451 control digital tube display mode to achieve marquees, flashing mode C language
ADPdigital-display
- 飞思卡尔16位单片机，实验板上单片机AD模块的AN15引脚接了可调电位器RV1（见实验板原理图），要求实现对可调电位器上的电压进行AD转换（ 10位精度），并对采样结果进行数字滤波，即对采样多次（如10次）的结果排序并掐头去尾求平均值，将滤波后的结果（转换成十进制）送四位数码管显示-Freescale 16-bit microcontroller, experiment board microcontroller AD module AN15 pin is connected to an adj
MSP-EXP430F5529
- MSP430F5529 USB 实验板- MSP-EXP430F5529 的初始代码 -MSP430F5529 USB experiment board- MSP-EXP430F5529 initial code
cmd
- DSP实验板所需要的.cmd文件，适用于多数DSP开发板使用-DSP experiment board needed. Cmd file, for most DSP development board