搜索资源列表
111-(2)
- 本系统主要由Zigbee无线传感器网络,基于ARM-Linux平台的嵌入式网关,本地上位机监控软件和远程Internet监控软件四部分组成。网络节点设备主要由Zigbee模块和以MSP430F149单片机作为控制芯片的数据采集模块组成,主要采集井下温度,甲烷等环境参数。根据功能,网络节点设备可分为网络协调器设备,具有网络路由和终端功能的定位参考节点设备,待定位的移动盲节点设备三种。系统工作时,协调器上电负责网络初始化和建网,定位参考节点和移动盲节点上电后自动搜寻网络并加入网络,-The sys
DHT11-temperature
- DHT11温湿度无线采集,串口接收显示,线性显示图形,最多支持四个数据采集-DHT11 temperature and humidity wireless acquisition, serial receiver display, linear display graphics, supports up to four data collection
cc2430-ds18b20
- cc2430使用ds18b20温度传感器采集温度数据并通过无线的方式传输到另一个节点。-cc2430 ds18b20 temperature sensor using temperature data collected and transmitted by wireless to another node.
RF_Example_Code
- CC430单片机的无线对发数据,用于两节点之间的通信-CC430 microcontroller wireless data on the hair for communication between two nodes
75448141GPRSDemo
- 一个实现GPRS无线上网的程序,通过AT指令来控制GPRS模块实现TCP/IP传输文件数据-A program to achieve GPRS wireless Internet access via AT commands to control the GPRS module TCP/IP transport file data
car-wireless
- 手势遥控小车,通过倾角模块检测角度变化,无线24l01发送数据,Lm293驱动小车。-Gesture remote control car, through the inclination angle of the module detects changes in the wireless 24l01 send data, Lm293 driven car.
msp430f149
- MSP403F149对两路电流两路电压分别采集,并采集两个温度,计算功率。将每路电流、每路电压、功率、两个温度显示在12864液晶屏上。对电流电压监控实现超限报警,并利用Zigbee无线网络将这些数据发送到上位机进行实时监控。- It can sample two currents and two voltags based on MSP430F149 MCU, collect two temperatures and compute power. Displaying current, vo
SampleApp-temperature1
- 节点温度传感器,运用zigbee无线传输温度值给协调器,再经协调串口传输数据给上位机-Node temperature sensors, temperature values using zigbee wireless transmission to the coordinator, and then coordinated serial transmission of data to the host computer
APC220
- 介绍APC220无线传输模块的使用,以及用51单片机测试程序。介绍上位机与下位机的数据传输方式。-Introduction APC220 wireless transmission module used, and with 51 testing procedures. Introduction PC and the next crew of the data transmission.
WeBEE-CC2530
- CC2530 2.4G无线通信模块串口发送数据,通过无线口发出,无线接收到信号,转发给串口-CC2530 2.4G wireless communication module serial port to send data through the wireless port issue, the wireless signal is received, forwarded to the serial port
test_send
- 实现无线通讯芯片24L01的数据发送 并可以选择通道 应用于51单片机上-24L01 wireless communication chip data transmission and you can select the channel used in the SCM 51
wuxianwendu
- 单片机STC89C52通过NRF2401无线传输从DSB18B20采集到的数据,包括发送程序和接收程序-STC89c52 NRF2401 DS18B20
Wireless-data-transmission
- 单片机系统控制NRF905无线通信模块实现数据的无线传输-SCM system control NRF905 wireless communication module for wireless data transmission
wifi-module
- 2.4G无线模块NRF24L01成功驱动,可以收发任何数据,并且反应很快,最大距离可以达到10米-nrf24l01 drive successfully
DEEC1VSDEEC2
- 无线传感器网络协议的数据传输对比以及能量消耗对比-Wireless sensor network data transfer protocol and the energy consumption comparison Comparison
leachm1
- 无线传感器网络协议仿真,可以看到每一轮所选出的簇头数目,基站收到的数据包总数,簇头收到的数据包总数,第一个节点死亡的时间,10 的节点死亡的时间等-Wireless sensor network protocol simulation, you can see every one of the selected number of cluster heads, the total number of packets received base station, cluster head tota
fps
- 无线传感器网络协议仿真对比,死亡节点数随时间的变化对比,传输到基站的数据对比,网络能量消耗对比以及生命周期和稳定周期对比等-Wireless sensor network protocol simulation contrast, death nodes comparing the change with time, comparison of the data transmitted to the base station, network energy consumption and lif
ZLDL_ShuangBiHuanZhongDuan
- 张力调节程序的双闭环实现及数据的无线传输-DSP and wireless module for wireless data transmission
wireless-communication
- 基于单片机的无线通信,可以双向实现数据的收发-Microcontroller-based wireless communications, two-way data transceiver
CT8022_program
- 此程序先对CT8022进行初始化设置,设置其工作在G.723.1压缩语音数据模式,PCM3500工作在主模式,CT8022工作在从模式,帧同步信号8kHz,位同步信号128kHz,16bitCODEC采集模拟语音信号后传给CT8022,CT8022将压缩后的数据通过无线模块传PC,PC通过串口调试助手接收数据-this program is made for voice compression device CT8022,and CT8022 is working in the G.723.1