搜索资源列表
StepDriverC8051
- C8051的两相四线步进电机测试程序，开发环境为keil c-C8051 two-phase four-wire stepper motor test program development environment for keil c
105230326motodrive
- 使用labview开发的步进电机控制及测控数据采集程序代码-labview motor control and data acquire source code
00369
- 对步进电机原理和驱动方式的详细介绍及分析，对我们在做步进电机驱动程序和硬件电路时很有帮助-Principle of stepper motor and drive means a detailed descr iption and analysis, we are doing stepper motor driver and the hardware circuit helpful
09NECL298n
- 此为09年电子设计大赛的电机驱动程序，电机为步进电机，驱动为L298和nec的控制芯片组成-This is the 2009 Electronic Design Contest of the motor drive, motor for the stepper motor, driver for the L298 and the control chips nec
HongWaiXiaoChe
- 这是参加电子设计大赛时的作品：红外遥控小车：用红外线通过一块AT89S52单片机发射信号即编码，并用红外接收头接收信号；接着再用另一块AT89S52单片机对红外发射出的信号编码进行解码，最后再用一块AT89S52单片机用解码所得码值编写程序后驱动步进电机。步进机功能启动后不仅能使受控小车向前后左右四个方向前进和转弯，而且还能控制小车再地上转动并留下方形或圆形等形状。-This is the time to participate in Electronic Design Contest work
bu1
- 步进电机以加速方式启动，转速达到程序规定的最快速度后保持一段时间匀速运转，又开始以减速-Stepper motor starts to accelerate, speed up procedures required to maintain the fastest pace for some time after the constant speed operation, but also begin to slow down
EX16_Step
- dsp2812步进电机控制源代码，可以驱动步进电机，也可以作为dsp初学者调试程序，程序完整，包含所有头文件，可以在主函数文件中根据需要增加功能-dsp2812 stepper motor control source code, you can drive a stepper motor, but also can be used as dsp beginner debugger, program integrity, and contains all the header files, yo
djkz
- 一个可控制步进电机正反转的程序,包括c源文件,hex文件,proteus仿真文件-One can control the stepper motor positive inversion procedures, including the c source file, hex file, proteus simulation file
mot
- 该程序可以驱动常见的两相4步的小型步进电机并且可以通过按键控制电机加速减速暂停正反转。并且将相关信息显示在数码管上。-The program can drive the common four-step two-phase stepper motors and can be a small button to control motor speed reducer through the suspension of positive inversion. And relevant informa
StepMotor@l298n
- 用L298N实现两相四线步进电机的控制，程序在51单片机上调试通过，控制口P1.0~P1.3-With the realization of two-phase four-wire L298N stepper motor control, program debugging through the MCU 51 to control the port P1.0 ~ P1.3
StepperMotorports
- 基于FPGA环境下步进电机控制模块程序实现-FPGA-based stepper motor control module Environment Program Realization
step-motor
- 本文介绍了步进电机的控制算法，运动曲线的制定，并给出了完整的驱动程序。-This article describes the stepper motor control algorithm, sports development curve, and gives a complete driver.
bjdj
- 步进电机驱动源程序 /* 1、本程序用于测试4相步进电机常规驱动 2、需要用跳帽或者杜邦线把信号输出端和对应的步进电机信号输入端连接起来 3、速度不可以调节的过快，不然就没有力矩转动了 可以按照给的原理图接线 接P1.1-P1.4 */-step motor
dsp-stepcontrol
- 一个DSP控制步进电机的程序，含控制部分原理图-A DSP controlled stepper motor procedures, including control over portions of the schematic
shengguoqi
- 基于51的使用步进电机控制升旗程序c语言-Stepper motor control based on the 51 flag-raising program c language
bujindianji
- 步进电机驱动程序，以及调速程序，带注释的，简单易懂-bujingdianji
EX16_Step
- TMS320F2812控制步进电机的小程序，是我买的电路板QQ2812上的程序，经本人调试，完全可用。但是直接只能驱动很小的电机，大电机要有驱动器-TMS320F2812 control the stepper motor a small program that I bought a program on the circuit board QQ2812, after I debug, fully available. However, can only be driven directly
113172223bjdjKZSD
- 单片机步进电机控制程序 可以控制加速减速的程序可以正反转-Microcontroller stepper motor control program can control the acceleration and deceleration of the programs can be positive inversion
Moter
- 步进电机转速控制程序：可以通过电位器来精确调节电机的转速的-Stepper motor speed control program: can potentiometer to fine tune the motor speed
bj
- 步进电机12864显示仿真+程序可以显示步进电机的步数-Stepper motor 12864 show simulation+ program can display the number of stepper motor steps