搜索资源列表
Speedbike
- 单片机做的自行车测速源程序，带PROTEUS仿真图，原理清晰可见，易懂。-Single-chip source gun to do the cycle with PROTEUS simulation map, the principle of clear, easy to understand.
UART_MEGA128
- uart测速程序，采用C语言编程，已经板上编译成功-uart velocimetry procedures, the use of C language programming, has been successfully compiled on the board
count
- 智能汽车测速用码表，精切到百分秒，检测电路简单，只需一对红外发射接收管和lcd1602便可。-Intelligent Vehicle Speed code table used, the percentage of precision-cut second detection circuit is simple, just a pair of infrared emission will be able to receive control and lcd1602.
1
- 直流电机的测速和液晶中文的显示，相信大家会喜欢-DC Motor Speed and LCD display in Chinese, I believe we would all like to
tuxiansibie
- 根据功能的不同，小车分为六部分：摄像头图像采集模块、电源模块、电机驱动模块、测速模块、舵机转向模块、辅助调试模块-According to the different features, car is divided into six parts: image acquisition camera modules, power modules, motor drive modules, gun modules, gear shift module, auxiliary debugging mod
danpinji
- 步进电机\18B20测温\电机测速\显示及键盘、定时器、七段码显示-you can find every experement about the
t1
- 实现电机M/T法测速的VHDL代码，只要修改cnt值大小即可修改M/T法切换的频率，当小于cnt时为T法，大于时为M法。-Motor M/T method velocimetry of the VHDL code, as long as the modified value of cnt to modify the size of M/T method of frequency switching, when cnt is less than for the T method, for M gr
A
- 用AVR单片机编写的汽车测速程序，其中包含了仿真图形，已经调试通过。这是我的毕业设计。希望给大家做个参考吧，采用1602显示，可以精确到小数点后6位，这个程序也可以改为测转速或者测频率。-Prepared using single-chip automotive AVR velocimetry procedures, including graphics simulation, debugging has been through. This is my graduation project.
DC_Motor
- 直流电机测速调速,分10级进行加减调速，并实时测量转速-DC Motor Speed Control, sub-10 speed control for addition and subtraction, and real-time measurement of speed
etc
- 基于mc9s12xs128单片机的etc测速显示模块程序-Based on SCM mc9s12xs128 gun display module procedures etc
Demo
- 使用T1作为定时器（定时时间为50毫秒），T0作为计数器（计数由电机测速电路产生的脉冲个数，每转4个脉冲），每1秒时间后，读出T0的值（读出后须将T0清0），将该值（速度值*4）显示到LED数码显示器上-The use of T1 as a timer (time of 50 ms from time to time), T0 as a counter (counting from the electrical pulse generated by gun circuit number, 4 p
lty
- 电机测速带调整-Electric gun with adjustment
test
- 一. 实验目的： 1.了解光电开关的使用方法 2.了解利用光电传感器测量电机转速的方法 二.光电测速基本原理 光电测速的基本电路由光电传感器、计数器和定时器组成。测量时在被测电机主轴上固定一个圆盘，圆盘的边缘上打上小孔。传感器的红外发射端和接收端装在圆盘的两测，电机带动圆盘转到有孔的位置时，红外光通过，红外接收管导通，输出低电平。红外光被挡住时接收管截止，输出高电平。用计数器记录在一定时间内传感器发出的脉冲个数就可以计算出电机转速。 三.实验内容 1.接线方法
PID
- 经过老师的指导:速度采样用M法不适应低,所以对于调速范围大的就用M/T法,适合于高低测速!对测速还要加以数字滤波!可用一阶惯性/中值法,平均法等!-After the teacher' s guide: the speed of the sampling method are not suited with M low speed range for the use of the M/T method, suitable for the level of gun! Gun would al
Src
- 此程序用于实现直流电机的正转与反转、测速与PWM调速。-For the realization of this process is DC motor with reverse switch, Speed Control and PWM.
bike_speed
- AVR实现自行车测速，将速度显示在液晶上，将上次行驶的距离保存在EEPROM内。-Bicycle Speed AVR to achieve will be the rate displayed on the LCD would be the last moving in the distance stored in the EEPROM.
cs
- 单片机测速原理 富有程序 内容很详细 富有电路图-Single-chip full of guns to the principle of the procedure is very rich in detail circuit diagram
TrackingandSpeed
- 集合了循迹，用霍尔传感器测速，pwm控制驱动使能端调速，温度读取显示到12864液晶屏上去。-Set the tracking, with Hall sensor gun, pwm control drive speed enabled client, the temperature read LCD display up to 12864.
motorspeedsurveysystem
- 比较全面的直流电机测速系统，桂林电子科技大学论文-motorspeedsurveysystem
ceshu
- 小车利用霍尔元件测速，并把速度显示在LCD上。单片机C语言程序-it s good