搜索资源列表
低频数字式相位测量仪
- 低频数字式相位测量仪； 此系统由相位测量仪、数字式移相信号发生器和移相网络三部分组成。为使系统更加稳定，使系统整体精度得以保障，本电路两块T89C52为核心控制器件分别控制相位测量、数字式移相信号发生,在数字式移相信号发生部分采用了锁相技术、CPLD等技术, 使输出波形精度大大提高，并可对频率自动校验，提高频率稳定性。-low-frequency digital phase-measuring instrument; This system consists of phase-measuri
step3(角度测量)
- 用鼠标绘制的两直线间角度的测量(利用余弦公式)-drawn with the mouse between the two linear and angular measurements (using the cosine formula)
labview3D 测量
- 基于labview开发的PLC串口通讯工具labview3D 测量，非常方便使用(The PLC serial communication tool based on LabVIEW is very convenient to use)
RLC测量仪
- 用单片机实现电阻（不同阻值范围）与电容的测量(The measurement of resistance (different range of resistance) and capacitance by single chip microcomputer)
基于声音与振动工具包的振动测量分析
- 基于声音与振动工具包的振动测量分析Vibration measurement and analysis based on sound and vibration Toolkit(Vibration measurement and analysis based on sound and vibration Toolkit)
多点温度测量
- TI msp430温度测量的原文件 可以多点测量温度 串口通信(The original document of TI MSP430 temperature measurement)
测量高度差
- 测量两图像间的高度差，通过提取图像边缘，测量两图像间高度差(he height difference between the two images is measured, and the height difference between the two images is measured by extracting the edge of the image.)
频率测量
- 该程序实现频率测量，程序简洁明了，功能强大，适用于教学研究(The program realizes frequency measurement. The program is concise and clear, powerful, and suitable for teaching research.)
通道2测量电位器
- 使用tlc1543，构成测量电位器，相关电路连接及编程测试。(Use TLC1543 to form measuring potentiometer, relevant circuit connection and programming test.)
解析空中三角测量
- 实现解析空中三角测量，通过程序的设计深入理解解析空中三角测量的整个过程(The triangulation is analyzed and the whole process of air triangulation is understood through the design of the program.)
测量电容电阻
- 利用C52单片机和NE555测量电容电阻 并显示(Measuring capacitance)
单目测量
- 基于MATLAB实现机器视觉中通过单幅图像实现测量长度，面积等(Based on MATLAB, we can measure the length, area and so on through single image in machine vision.)
摄影测量
- 武大摄影测量全套书籍 内含6本院士书籍(Photogrammetry WuHan University)
测量4-工具变换测量
- 机器视觉，利用halcon实现工件的长度测量(Machine vision, using Halcon to measure the length of workpiece)
电流互感器SUI-101A说明书及测量值读取程序
- 电流互感器SUI-101A说明书及测量值读取程序(Instructions of Current Transformer SUI-101A and Reading Procedure of Measured Value)
测量程序 (2)
- 空中三角解析测量，用于摄影测量中的地面点位置测量(Aerial Triangular Analytical Measurement)
练习11-写入测量文件
- 这是一个自己用LABVIEW编写的写入测量文件，用于将测量采集到的数据写入文件保存或者是再调用数据。(This is a write measurement file written by LabVIEW, which is used to write the data collected from the measurement to the file for saving or re calling the data.)
MATLAB平面参数测量系统（GUI，面积，周长参数）
- 一、课题介绍：本课题为基于MATLAB的平面参数测量系统，是以一个带缺陷的光伏面板作为素材，检测出缺陷所在，定位后计算出每个缺陷的面积大小。本设计带有一个人机界面GUI. 二、算法流程：读入测试图片——rgb转换——分割——开闭运算——空洞填充——过滤微小连通域面积——计算缺陷面积和个数。(1. Topic introduction: this topic is a plane parameter measurement system based on MATLAB. It uses a ph
温度测量
- 基于stc12c5108s2单片机的温度测量的原理图和程序，使用单片机和TMP35和pt100实现温度测量，包括原理图、C语言程序和测试结果(Based on the schematic diagram and program of temperature measurement based on stc12c5108s2 single chip microcomputer, the temperature measurement is realized by using single chip
转速测量
- 基于stc12c5a08s2单片机使用M/T法测量频率(Based on STC12C5A08S2 microcontroller, M/T method was used to measure the rotating speed)