搜索资源列表
ADCswitch
- 51单片机电容式触摸开关的基本设计源码,可以将单片机某一引脚直接变为触摸式的开关,或者实现简单的触摸按键-51 single-chip capacitive touch switch of the basic design source code, you can turn a single chip directly into a touch switch, or to achieve a simple touch button
stm32f1test
- ADD:这个模块我在调试过程中发现很容易便会死机,对干扰跟电源扰动比较敏感,过段时间试试加个电容减少下波纹。SI4463具有RSSI功能,与WIFI一样可以通过这个来估计距离,不太清楚其信道评测功能,将继续研究以便实现自动跳频-ADD: this module I found in the debugging process easily will crash, disturbance is more sensitive to power, the interference over time
emWin5.24_yuanzi
- emwin在stm32下移植的工程,屏幕为原子的7寸电容屏,在工程下做了几个小界面,如计算器等,工程可以直接编译下载。-emwin at stm32 transplant works, the screen is 7 inch capacitive screen atoms, in the project to do a few small interface, such as calculators, projects can be compiled directly download.
ESS_UC2_Maxwell
- 关于超级电容在matlab中的仿真应用,代码中包含变量声名及其他内容-the application of matalab about simulation of ultracapacitor
STM32F4-
- STM32F4 电容触摸液晶屏移植 STM32F4 电容触摸液晶屏移植-STM32F4 capacitive touch LCD screen
AC-Down
- 电容降压阻容计算含具体算法和选型电容降压原理图和设计图-Capacitor step-down resistor-capacitor containing specific algorithm to calculate and selection
cap
- 本代码是基于STC89C52单片机最小系统开发环境的测量未知电容电路。根据555定时器的不同电容充放电时间得到未知电容值。-The code is based on the STC89C52 MCU minimum system development environment for the measurement of unknown capacitance circuit. According to the different capacitor charge and discharge t
STM32F103-V3.5
- 1,本文件夹包含53个标准例程,所有例程均在战舰V3 STM32F103开发板上测试通过。 2,本文件夹下所有用到LCD的例程,都支持ALIENTEK 2.4/2.8/3.5/4.3/7寸电阻/电容触摸屏。 3,本文件夹下的所有例程,都是采用MDK5.14编译器。 4,编译生成的.hex文件(可以用来下载到开发板的)都存放在工程/OBJ文件夹里面。 -1, 53 standard routines, this folder contains all the routines
gslX680_A31S
- 已经调试通过的思立微gslX680电容屏驱动程序,我的是在A31s平台。-Reith legislation already debugging micro gslX680 capacitive screen driver through, and I was in A31s internet.
gui_dyn_14_3
- 动态电路分析,用户输入电阻、电容、电容初始电压。-Dynamic Circuits, user input resistance, capacitance, initial voltage of the capacitor.
power-circuit
- 在电源输入的前端利用旁路去耦电容滤波器,在+12V输入时,首先通过一个电解电容C1和电容C2保证电压的输入稳定,之后选择利用稳压器NCP1117ST50T3G将输出电压降到+5V,如图3.5所示,其输出电流为1A。在稳压器之后继续采用一个电解电容C3来保证输入到芯片的供电电压稳定。-Power input at the front end of the use of bypass decoupling capacitor filter when+12V input through a first
25fb_drv_doublebuffer
- 开发板4412_ARM9开发,通过framebuffer控制电容屏,设置部分驱动方法:* 需要先关闭内核中的framebuffer驱动,否则会冲突 make menuconfig -> Device Drivers -> Graphics support -> Samsung S3C framebuffer support 同时要确保CONFIG_FB_S3C_NR_BUFFERS生成 程序里面有详细注释,中文注释-Development board 4412_
una
- 用于MMC桥臂计算,特别适用于较为复杂的MMC平衡子模块电容电压的计算-MMC is used to calculate the arm, especially for more complex calculations MMC submodule capacitor voltage balance
MultiFuncTool-code-
- 基于LM3S811多功能手持终端,可实现电压,电容,电感,频率的测量-Based LM3S811 multi-function handheld terminals, voltage, capacitance, inductance measurement
Single-ended-capacitance-measurement
- 通过FDC1004测量电容,电容容量为小于100PF,使用的处理器是STM32F103,采用的方式是单端测量。-Measuring capacitance by FDC1004
FACTS
- FACTS-串联补偿 的基本思想是在输电线上串联接入设备,以改变线路的静态和动态特性,达到改善电网运行性能的目的。 串联补偿普遍应用的是无功补偿,一般是在线路中串入固定电容或电感。 -The basic idea FACTS- series compensation series-compensated transmission lines are connected in series on the access device, to change the static and dyn
FM01BTS
- FM01BTS、 FM01BTD 是一款低功耗并具有高性能的电源管理 IC,主要针对锂电池充电器而设计,与简单低成 本的 RCC 电路相比省去碳膜电阻一个、绦纶电容一个、 IN4148 二极管一个、 SS8050 三极管一个、稳压管一个, 最大程度的节约了系统成本,除了为用户提供高性价比的 AC/DC 电源系统应用以外,而且 IC 内部高度集成了欠压 锁定,过压保护,过温保护,限流保护,开短路保护等功能,使得 IC 的工作寿命大大延长。-CURRENT MODE PWM CONTRO
danpianji
- 1.晶振,至于大小由你单片机时钟周期要求而决定(用于计时,与两个电容并联使用,电容大小由你的晶振决定,一般用22pF) 2.复位电路(用于复位) 3.电源(用于供电,一般用电脑的USB口供电) 4.烧制程序的口(可用串口配合MAX232配合使用,也可以做个并口输入,这个要根据你使用单片机的种类决定,比如ATC可用并口,STC一般只用串口输入等等)-Crystal, as the size of your microcontroller clock cycle requirements
goodix
- 有关linux 下电容屏驱动的范例程序,指导如何写Linux的电容屏驱动,不错-On the capacitance of the Linux-driven example of the procedure to guide how to write Linux capacitive screen drive, good
altium-designer-
- altium designer原理元件库封装库包含各种常用元件库 电容 电阻 声亮器件 插件 继电器类器件78稳压系列 常用单片机 开关 等-Principle component library packaging library contains a variety of commonly used components library capacitance resistance sound light device plug-in relay device 78 voltage regu