搜索资源列表
直流电机
- 次程序为单片机89S52系列直流电机驱动程序,具体解释见程序.-meeting procedures SCM 89S52 series DC motor drivers, specific explanation procedures.
直流电机Proteus+arduino
- 基于Arduino和proteus的直流电机驱动仿真
MSP430单片机与L298驱动控制单片机正反转直行后退
- MSP430单片机与L298驱动控制单片机正反转直行后退 基于IAR for MSP430F16X
PWM.rar
- PWM产生程序，可以利用此程序，加上后续的放大来驱动直流电机,PWM generation process, we can use this procedure, together with the follow-up to drive the DC motor to enlarge
H_bridge_motor
- 常用H桥芯片，内附详细资料。可用于驱动直流电机-H bridge chips commonly used, containing detailed information. Can be used to drive DC motors
bldcm_control
- 无刷直流电机驱动程序，采用六段换相控制程序，可用于六管三相全桥驱动电路的无刷直流电机控制。-Brushless DC motor driver for the use of six-phase control procedures, can be used for six three-phase full-bridge driver circuit of brushless DC motor control.
DirectCurrentMachine
- 基于51单片机的直流电机驱动,外加1602显示-51 single-chip microcomputer-based DC motor drive, plus 1602 show .....
L298_motor
- L298N驱动直流电机程序，C语言，编译环境keil，mcuAT89S52，调试仿真实测通过。-DC motor driver L298N process, C language, compiler environment keil, mcuAT89S52, measured through the simulation debug.
motor
- 用298n驱动两个直流电机，具有正反转、PWM加减速控制-298n drive with two DC motors with a positive, PWM speed control
direct_moto
- 基于FPGA的直流电机驱动，有32级速度选择，正反转和使能端。在硬件测试通过，效果良好-FPGA-based DC motor drive, there are 32 speed options, positive inversion, and enable end. On the hardware test results were very good
DCmotor
- 这个是TMS320F2812的DSP直流电机驱动程序，对c2000 DSP初学者有很大的帮助！-This is the TMS320F2812 DC motor driver for the DSP, the c2000 DSP beginners great help!
PWM电机 - 副本
- 驱动直流电机，通过l298n来驱动，stm32板拉高引脚PA9与PA10，同时PA7输出PWM值(The drive DC motor is driven by L298N, the STM32 board pulls the high pin PA9 and the PA10, and the PA7 outputs the PWM value)
蓝牙+小车（C8T6）
- 一个简易的基于STM32F103系列平台以及L911电机驱动模块的蓝牙通信，通过客户端向单片机发送测试数据控制小车移动。(A simple Bluetooth communication based on the STM32F103 Series platform and L911 motor driver module, through the client to send test data to the microcontroller, control the movement of th
ArduinoBalanceCar-master
- 基于 arduino 的自平衡轮算法，无刷电机驱动(Self balancing wheel algorithm based on Arduino, brushless motor drive)
lab18-PWM
- 下载到CCS6.0软件中，用来驱动无刷直流电机(Used to drive brushless DC motor)
步进电机
- 驱动步进电机的简单c51小程序，亲测可用(Simple stepper motor driver C51 applet, pro test available)
直流电机速度PID控制
- 光电编码器测得的电机速度反馈信号反馈到单片机中。电机设定速度由ZLG7289模块获得，通过SPI通信传输给单片机。单片机系统根据给定的转速与反馈回来的实际速度相减得出偏差，经过控制算法得出控制量。单片机再把控制量以PWM的形式输出，经过L298功率放大驱动直流电机。ZLG7289模块主要用于显示当前直流电机实际转速和给定转速，并让用户通过键盘输入设定速度。(The motor speed feedback signal measured by the photoelectric encoder
驱动电机
- 通过读取光栅传感器的输出脉冲个数进而控制直流电机转动相应的距离。(By reading the number of output pulses of the grating sensor, the corresponding distance of the DC motor can be controlled.)
MKK_72V_28035_NewStruct_CCS5_CAN
- 基于28305的无刷直流电机驱动控制，使用的是CAN通信(Brushless DC motor drive control based on 28305, using CAN communication)
LUNCHPADMSP430G2553L298电机驱动
- 能够驱动5v-12v直流电机电动小车的驱动不但要求电机驱动系统具有高转矩重量比、宽调速范围、 高可靠性，而且电机的转矩 -转速特性受电源功率的影响，这就要求驱动 具有尽可能宽的高效率区。(The drive of 5V-12V DC motor electric car requires not only the motor drive system with high torque-weight ratio, wide speed range and high reliability, but