搜索资源列表
Watcher
- 这是一个红外温度探头测试程序,用于对温度探头进行测试,同时也可以作为温度采集用。由于探头通过RS232与计算机连接,所以程序包括串口通信的实现,串口通信利用了第三方通信类CSerial。程序可以将测得的数据保存为Excel文档。-This is an infrared temperature probe testing procedures used to test the temperature probe, but also used as temperature acquisition.
DS18B202051
- 基于2051芯片用18b20做探头的温度显示器。
4_wendu_baojing
- 这个是4路温度检测程序和相关的电路板文件,可轮流扫描4路DS18B20文件并报警,可分别独立设置4路探头的上下限温度,数码管显示,显示分辨率0.1度-This is a 4 channel temperature testing procedures and the associated board file can be scanned in turn 4 DS18B20 file and alarm can be set independently on the four lower tem
1820
- 1820温度的探头有较高的精度和1284显示-1820 temperature probes have a higher accuracy and 1284 show
lcdtemp
- DS18B20温度显示实验 数码管显示温度值,精确到小数后面2位值 * * 使用时将DS18B20温度传感器插入对应插座中运行即可 * * 用手拧住温度探头,就可以看到温度值的变化!-DS18B20 temperature display digital tube experiments showed that the temperature value, accurate to two decimal value back** used to insert the corre
get_6675_temp_2
- MAXII 240 CPLD和6675 开发的0-1023.75度的温度传感数据采集系统,用seg7 LED显示,精度0.25度。探头是K型测温线,Quartus II 6.0调是通过,在cpld开发板上面试验成功-MAXII 240cpld and 0-1023.75 development of 6675 degrees C temperature sensor data acquisition system, using seg7 LED shows that the accuracy o
VB0922
- vb开发的读取温度探头温度的小程序,有文件加密解密功能!-vb development of the temperature probe reads the temperature of small procedures, file encryption decryption function!
18B20
- 1. 用18B20或AD590温度传感器作温度探头,采集温度数据并转换成BCD码在数码管上显示。 2. 记录间隔可任意设定(1S到1h,步长1s),能按设定时间存储数据。 3. 通过键回放温度和记录时间参数。 4. 设定温度告警门限。 通过声、光告警显示 -1. 18B20 or the AD590 temperature sensor using the temperature probe, temperature data collected and converted
DS18B20
- 本程序需要1602字符型液晶模块及DS18B20温度传感器支持,通过1602液晶模块显示DS18B20状态及实时温度,正常情况下1602的第一行显示“DS18B20 OK!”,第二行显示实时温度 * //* 如果DS18B20不存在,则显示“DS18B20 Error Please Check!” * //* 表示DS18B20错误,请检查,同时蜂鸣器发出“嘀嘀”报警声 * //* 用手拧住温度探头,就可以看到温度值的变化-This program requires 1602 Cha
TEMPERATUResensing
- 将红外探头输出的模拟信号差分放大后,用AVR单片机进行ADC转换,通过相关算法和参考温度标准获得实际温度值-sensing temperatures by ultrared sensor
18b20
- 51单片机的18b20数字温度探头的程序。很适合新手用-51 SCM 18b20 digital temperature probe procedures. Very suitable for novice use
wenkong-last
- 采用STC90C516RD+单片机芯片控制最小系统,从DS18B20防水温度探头测量温度,并显示1602液晶上。温度控制由单片机内部定时器控制继电器开关来加热并计时。时间显示利用时钟芯片1302设置和读取日期时间同时显示在液晶显示屏上。-failed to translate
Cewen_M8
- 红外探头实现测温功能,ATmega8L单片机控制程序,实现电压温度的转换。-Infrared sensor realize temperature measurement function, ATmega8L single-chip microcomputer control programs achieve voltage temperature conversion.
DllcdtempS
- DS18B20温度显示实验 数码管显示温度值,精确到小数后面2位值 * * 使用时将DS18B200温度传感器插入对应插座中运行即可 * * 用手拧住温度探头,就可以看到温度值的变化! 已通过测试。 -The DS18B20 temperature experimental digital display temperature values, accurate to two decimal behind value** use the DS18B200 temperature sensor
TEMP
- 利用电脑串口与单片机通信,实时测试温度探头的温度并且记录。附源文件,有兴趣的可以研究下-Computer serial port to communicate with the microcontroller, test the temperature of the temperature probe in real time and record. Source file, interest can be studied under
ntc_3470
- 空调温度探头4.7K-3470-ntc查找表。-4.7K-3470-ntc table
PIC_gettemp
- 用PIC单片机实现的温度传感器,可级联通信,此为温度探头的代码,可用。温度传感器用的是DS18B20,MCU用的是最小型的PIC8脚单片机 PIC12F509.注意前面的配置字.程序经测试通过!-PIC MCU with temperature sensors can be cascaded communication, this is the temperature probe of the code, is available. Temperature sensor is DS18B20,
多通道温度记录
- 利用吉时利2700多通道万用表和PT100温度探头,实现5个通道的温度记录。(Ultilizing Keithley 2700 multichannel 6 1/2 DMM and PT100 temperature sensor, A temperature record of 5 channels is implemented.)
STM8S ds18b20
- STM8S挂接DS18B20温度探头实现高精度温度采集的程序库函数版。(STM8S hangs DS18B20 temperature probe to realize high precision temperature acquisition program library function edition.)
AD5934驱动程序(stm32)
- AD5934 stm32f103驱动程序; 测量PT100温度探头计算温度; 测量电极间阻抗并换算成电导率。(AD5934 stm32f103 driver; Measuring the temperature of the PT100 temperature probe; The impedance between the electrodes is measured and converted into conductivity.)