资源列表
AD9850
- AD9850并行串行测试程序。芯片原理图，英文数据手册，串行AD9850使用手册，基于AD9850可编程信号发生器的设计等相关设计论文。-AD9850 Parallel Serial testing procedures. The chip schematic data sheet in English serial the AD9850 use of manual, based on the design of the the AD9850 programmable signal genera
multiple-function-electronic-clock
- 基于 1602 ds 12b80 ds 1302 的多功能电子表 -based on 1602 ds12b80 ds1302 multi-function electronic clock
Control-Cross-Road-Traffic-Display
- pic16f877的TMR1与TMR2控制十字路口秒计时显示屏-a pic16f877 The TMR1 and TMR2 control crossroads seconds chronograph display
flash
- Flash Write program in c-Flash Write program in c++
STM32_FFT
- 利用意法半导体提供的DSP固件库在STM103芯片上实现快速傅里叶变换FFT算法，开发环境使用Keil uVision4。-The DSP firmware library provided by the use of STMicroelectronics STM103 chip Fast Fourier Transform (FFT) algorithm, the development environment uses the Keil the uVision4.
ucGUIPznFATPSDPLCD
- 基于STM32的图形用户界面系统的设计（GUI），包括了文件系统FAT，SD卡和LCD的管理，开发环境使用keil uVision 4.-Based on the STM32 design of graphical user interface (GUI), including the file system FAT, SD card and LCD management, development environment keil uVision 4.
TCP_IP_Project
- 一个简化的TCP_IP协议栈的例子，对嵌入式设备上的以太网开发很有参考价值，开发环境keil uVision 4-Example of a simplified TCP_IP protocol stack the Ethernet development on embedded devices useful reference value, the development environment keil uVision 4
FIFO
- FIFO在VHDL上的实现。没有注释，较为完善，已通过编译。-FIFO implementations in VHDL. No comment, more perfect, has compiled.
electronic-clock-
- 利用单片机设计电子时钟，调制电子时钟的时间日期，闹铃，秒表，-Use of a single-chip design electronic clock, to modulation electronic clock time date, alarm, stopwatch, etc.
code
- 太阳能手提灯 带自动充放电保护功能，三档LED恒流调光，USB输出，C51单片机-Solar Lantern with automatic charge and discharge protection function, third gear dimming LED constant current, USB output
Interface
- 基于STM32的7寸液晶界面的开发，该液晶的控制IC为SSD1963；此界面是显示的一个计算器操作界面（没有计算功能）；编译软件为KEIL4；开发语言为C语言-Based on the STM32 development of 7-inch LCD screen, the LCD controller IC, SSD1963 This interface is the user interface displays a calculator (no calculations) compile
NRF905_1
- 基于STM32的NRF905通信模块调试。 功能：里面有8个按键，每次按下不同的按键，按键值都会被保存在同一个地址， 即0X29，很显然，上一个数据被下一个所替代，但是符合想要的功能。 数据在发送时，会有T_led指示灯闪烁，与之对应，当接收机接收到数据 后，R_led指示灯也会闪烁。自此，收发成功！-Based on the STM32 NRF905 communication module debugging. Function: There are eight bu