搜索资源列表
Single-Chip-LED-dynamic-scanning
- 单片机控制数码管动态扫描,隔一定时间自动加一。-SCM control digital dynamic scan, automatically add a certain time interval.
Plus-a-digital-dynamic-scanning
- 通过AT89X52单片机实现数码管动态扫描加1。-Plus a digital dynamic scanning
naozhongC51
- AT89S51单片机实现闹钟功能,数码管动态扫描方式显示当前时间和带设定的定时时间,按键设置定时时间,蜂鸣器播放音乐提醒时间到-AT89S51 MCU alarm clock function, digital dynamic scan mode displays the current time and with a set of regular time, regular time set buttons, buzzer reminder time to play music
miaobiao-design_Verilog_HDL
- 秒表有两个功能按钮:一个是计数和停止计数按钮,当第一次按下此按钮时,秒表开始计数,再一次按下时,秒表停止计数,并显示所计的数字;另一个是清零按钮,当按下此按钮时,秒表清零。在数码管上采用动态扫描显示输出。-Stopwatch has two function buttons: one button count and stop counting when the first time you press this button, the stopwatch starts counting, wh
4_3
- 利用动态扫描和定时器1在数码管上显示 出从765432开始以1/10秒的速度往下递减 直至765398并保持显示此数,与此同时利 用定时器0以500MS速度进行流水灯从上至 下移动,当数码管上数减到停止时,实验 板上流水灯也停止然后全部开始闪烁,3秒 后(用T0定时)流水灯全部关闭、数码管上 显示出"HELLO"。到此保持住。 设晶振频率为12MHz。-Dynamic scan and Timer 1 is displayed on the digital sta
4_1
- 利用动态扫描方法在六位数码管上显示出稳定的654321. 时钟频率为11.0592M-Dynamic scan method on six digital tube display a stable 654321. Clock frequency is 11.0592M
4_2
- 用动态扫描方法和定时器1在数码管的前三位显示出秒表, 精确到1 秒,即最后一位显示1 秒,一直循环下去 设时钟频率为12M-Dynamic scanning method and Timer 1 in the top three shows digital stopwatch, accurate to 1 of the second, that last one is displayed 1 seconds, until the cycle continues setting the
Digital-display
- 数码管动态扫描显示控制器的设计。用VHDL语言设计并实现六个数码管滚动显示电路。-Digital dynamic scanning display controller design. Designed and implemented using VHDL six digital tube display circuit scrolling.
Elevator
- 51单片机利用数码管动态扫描模拟电梯程序。-The use of 51 singlechip digital tube dynamic scanning elevator simulation program.
display
- 多位数码管动态扫描显示变化数据 显示小数点方法-Muchos escaneo digital dinámico muestra los cambios en el método de punto decimal de visualización de datos
dongtaisaomiao
- 基于avr单片机的数码管动态扫描程序的hex文件-hex
Dynamic-digital-display-chip
- 本设计利用人眼的“视觉暂留”效应,采用循环高速扫描的方式,分时轮流选通各数码管的COM端,使数码管轮流导通显示。-This design uses the human eye' s " persistence of vision" effect, with the way high-speed scanning cycle, time-gated turn the COM port of the digital control, digital control to tu
1234
- 带数码管显示的交通灯模拟控制系统设计. 硬件方面:8253产生1HZ的方波,脉冲到8259的IR1端,产生中断,调中断服务子程序。在加入紧急车道后,单脉冲()连到8259的IRO端,产生一个高级的中断请求信号。 软件方面:主程序先对各个硬件初始化,在开CPU中断,然后空操作,等待中断。执行低级中断(IR1)时,8255的PA口负责选数码管,PB口负责显示数字,用查表法可查到0~9的数码管编码。 采用循环扫描方法,人眼即可看到连续的二位数。当倒计时减到零时,对红绿灯取反。若手动上
LED_SCAN1
- FPGA 四位数码管的动态显示-数码管动态扫描模块-Dynamic FPGA four digital tube display- digital dynamic scanning module
main
- 用扫描方式读取四个独立式按键的键值,同时将 按键的键值在数码管上显示出来-By scanning way to read the key value of four independent type buttons, at the same time will be the keys of the buttons on the digital tube display.
text
- 八位七段共阳极数码管的显示,动态循环扫描。-Eight 7, a total of anode digital tube display, dynamic scanning cycles.
CNT999
- 使用VHDL设计999加法计数器,并使用扫描译码电路将数字显示在数码管上。顶层设计使用的原理图-Design using VHDL adder 999 counters, and use the digital scan decode circuit in the digital tube display. Schematic top-level design using
dynamic-display
- 51单片机动态扫描数码管,利用锁存器实现多个数码管显示-dynamic display
Digital
- 四位数码管驱动tm1637程序,按键扫描程序-Digital Driving tm1637
shumaguan
- 8个数码管全部扫描完后,再从头开始进行下一次扫描。编译正确-8 digital tube are scanned once, and then started from the first for the next cycle, a decimal point display. The correct compiler