搜索资源列表
c51_cstepmoto(128step)_l6219
- C51单片机实现128细分步进电机驱动程序,l6219驱动IC,6219是一个有两极的集成电路,它能控制和驱动具有两极步进电机的绕组, 还可以双向控制两个直流电机。L6219可以非常方便地与微处理器连接成控制步进电机的系统, 其电压范围可以从10V~46V,输出的电流可达到750mA,峰值电流高达1A。因为内部具有保护二极管及PWM电流控制, 所以在可靠性和稳定性方面提供了保障。单片机实现时将0~360℃作细分,一个步距角度是1.8℃,首先根据矢量合成图建立相应的向量表, 程序再
DIANJI
- 本驱动为LM298电机驱动,输出电流可达到2A左右。可驱动步进电机,直流电机。-The drive for LM298 motor drive, the output current can reach 2A. Can drive stepper motors, DC motors.
dianjiqudong
- 驱动两个直流电机,并实现加速,减速,向左转,向右转-Driven by two dc motors, and implement the acceleration, deceleration, turn left, turn right
zhiliudianjitiaosuchengxu
- 本设计采用AT89S52单片机为主控制器设计出一种基于PWM波控制直流电机的调速系统,通过微机和驱动电路可以实现电机的正反转,加减速调整-This design uses AT89S52 microcontroller-based controller design based on PWM wave control DC motor speed control system, through the computer and the drive circuit can be achieved
yaokong02
- DSP2812CAP口捕获航模遥控器PPM信号,转换成PWM 驱动H桥,驱动两个直流电机,已通过测试-DSP2812CAP port acquisition aeromodelling remote control PPM signal, converts the H bridge driver PWM, drive two DC motors, has been tested
BLDC-firmware
- 三相六拍直流无刷电机驱动固件,采用的TI的方案,已经用在我们公司的无刷圆锯上面了。特共享出来换积分-This is the driver for BLDC motor ,this firmware has been used on our BLDC product.
DC-motor-speed-control
- 通过开关或按键实现三个功能的切换:○1利用A/D转换芯片0809将W1电位器提供模拟量转换成数字量并显示;○2利用D/A转换芯片0832将单片机输出的数字量转换为模拟量输出并显示;○3利用W1电位器提供的模拟量经0809、单片机和0832转换和放大后驱动直流电机,实现电机调速。-Achieve three functions through the switch or button switch: ○ 1 use A/D converter chip 0809 will provide an a
L298N-Arduino-
- Arduino 的学习笔记,通过驱动板L298N来驱动两个直流电机,电子书PDF,书上附代码-Arduino study notes, two dc motor can be driven by L298N driver board, e-book PDF, the book attached code
SEED-BLDC-Kitv1.0(Rev.-A)
- 描述了三相无刷直流带电机驱动模板的使用说明,描述了seed-bldc的硬件构成,原理,以及实用方法和编程指导-Using the described three-phase brushless DC motor drive template with a descr iption, descr iption of the seed-bldc hardware structure, principle, and the practical methods and Programming Guide
pwm
- 用于直流无刷电机驱动,输出6路pwm波形 死区时间可控制-For brushless DC motor drive, 6 PWM waveform output dead time control
DJ
- 使用瑞萨G14能够通过IIC的控制直流电机的工作,从而实现电机的驱动。-Use Renesas G14 can control the DC motor IIC work, to achieve the motor drive
LPC213x-driver-for-DC-MOTOR
- nxp的ARMLPC213X系列的控制直流电机的驱动源码,并有串口通信功能!-nxp of ARMLPC213X series DC motor driver source code control, and serial communication functions!
motor-control
- L298通过pwm波驱动直流电机,电机为12v或者5v,是用51单片机开发的。-L298 pwm wave driven by a DC motor, the motor for 12v or 5v, with 51 MCU development.
BLDC-PMSM2-HALL
- 直流无刷电机的驱动,与交流伺服电机驱动大同小异-The brushless DC motor drive
Arduino-L293D
- 该类可以实现L293DN直流电机模块的驱动,-Arduino L293D
EX14_DCMOT
- DSP2812利用事件管理器产生两路互补的PWM波形驱动直流电机-DSP2812 using the event manager has two complementary PWM wave to drive DC motor
bxw
- 通过dsp2812控制直流电机的驱动程序。-Through the DSP2812 control of DC motor driver
PWM
- 51单片机利用L298N芯片驱动直流电机,通过按键PWM调速。-51 use L298N chip microcontroller drive DC motor PWM speed control via buttons.
shuzikongzhixitong
- 直流伺服电机驱动上位机,采集电机角度信号输出控制信号-Dc servo motor driver PC dc servo motor driver upper machine
DCmotortest.Zip
- 直流电机的驱动程序,使用LPC2131的PWM功能实现-DC motor driver, use the PWM functions to achieve LPC2131