搜索资源列表
Start12
- 这是飞思卡尔智能车电磁组的采用了中断设计的start12函数程序，用code warrior打开-This is freescale intelligent car of the electromagnetic group the interrupt design start12 function procedures, the use of code warrior open
SWJT
- 全国大学生飞思卡尔智能车比赛 电磁组原程序 整个系统的核心控制采用Freescale的MC9S12XS128型号16位单片机，5V电压供电。 软件运行需要配置单片机各个模块寄存器数值，使单片机各个模块正常工作。初始化中包括：单片机时钟配置、I/O口配置、PWM模块配置、A/D模块配置、RTI实时中断配置、脉冲捕捉模块配置。当初始化完毕后，开始对传感器输入信号进行采样，当完成一次采样后将采样值输入控制算法，控制算法经过运算得到应该偏转的角度和速度，通过改变PWM模块内部寄存器数值可以得到不同占空比
C14_FlashS1
- 飞思卡尔单片机mc9s12dg128 定时器溢出中断例程-Freescale the microcontroller mc9s12dg128 timer overflow interrupt routine
PIT-clok-of-mc9s12xs128
- 用定时器中断设计的秒表,使用飞思卡尔十六位单片机，适合飞思卡尔智能大赛入门使用-cloke use pit
PIT
- 飞思卡尔S12X单片机定时器中断驱动程序，分别设置四个定时器定时时间中断。-Freescale S12X MCU timer interrupt driver, set of four timer timing interrupt.
IRQ
- 飞思卡尔8位单片机入门 MC9S08AW32 如何进行中断服务设置-MC9S08AW32 for codewarrior interruption
TIMEROVERFLOW-FOR-TIMING
- 飞思卡尔dg128的实施溢出中断，相当于普通定时有参考价值-Freescale the dg128 the implementation of overflow interrupt, which is equivalent to the common timing reference value
IRQ_led_light
- 飞思卡尔HCS12X系列的IRQ中断测试工程，下降沿控制PB口LED灯亮灭，我在codewarrior 5.1上建的过程，运行在芯片MC9S12XDP512的开发板SK-S12XDP512-A上面。-Freescale HCS12X series IRQ interrupt test engineering, down along the PB mouth LED light control, destroyed in codewarrior 5.1 I built on the process
PIT_timer_interrupt
- 飞思卡尔HCS12X系列的使用中断法定时0.5s的PIT模块测试工程，我在codewarrior 5.1上建的工程，运行在芯片MC9S12XDP512的开发板SK-S12XDP512-A上面。-Freescale HCS12X series of use when the 0.5 s interrupt legal PIT module testing project, I in codewarrior 5.1 is built on the project, run on chips MC9S
IRQ_flow_overturn
- 飞思卡尔HCS12X系列的IRQ中断模块，下降沿控制PB口LED流水灯反显的工程，我在codewarrior 5.1上建的工程，运行在芯片MC9S12XDP512的开发板SK-S12XDP512-A上面。-Freescale HCS12X series IRQ interrupt module, down along the PB mouth water control LED lamp of reverse engineering, I in codewarrior 5.1 is built
SCI_interrupt
- 飞思卡尔HCS12X系列的SCI模块，采用中断发送和接收的工程，我在codewarrior 5.1上建的工程，运行在芯片MC9S12XDP512的开发板SK-S12XDP512-A上面。-Freescale HCS12X series of SCI module, the interrupt the sending and receiving engineering, I in codewarrior 5.1 is built on the project, run on chips MC9S1
demoXEPRTI
- 飞思卡尔S12XEP100定时中断实例程序，带中文说明-The Freescale S12XEP100 timer interrupt instance procedure, with Chinese instructions
xs128_RTI
- 飞思卡尔xs128，实施中断或是周期中断。测速，PID都会用到的。-Freescale xs128, implementation of the interrupt or periodic interrupt. Tachometer, PID will be used.
key-interrupt-experiment-
- 飞思卡尔单片机源代码——按键中断实验源代码-Freescale microcontroller source code- the key interrupt experiment source code
pit-12-09
- 周期性中断定时器的初始化配置以及使用方法 飞思卡尔-Periodic interrupt timer initialization to configure and use Freescale
Port-J-interrupt
- 飞思卡尔单片机外部中断端口J的触发中断，采用J6和J7-Freescale MCU external interrupt port J trigger interrupt
16-UART2_int
- 单片机_飞思卡尔_子程序,UART2中断发送接收,非常稳定的一款子程序-SCM _ the Freescale _ subroutine, UART2 interrupt transmission and reception of a very stable subroutine
Interrupt-partial-correction-Figure
- 中断部分修正图，用于飞思卡尔系列的单片机PCB制图-The microcontroller PCB cartography interrupt some correction map for Freescale Series
Timer-interrupt
- 飞思卡尔HCS12单片机定时器中断调试程序 适合飞思卡尔单片机初学者使用-Freescale HCS12 MCU timer interrupt debug program suitable for freescale microcontroller the beginner to use
Send
- 基于xs128核心的LED闪烁练习程序，适合参加飞思卡尔的新手们练习。包括基本初始化，时钟初始化、端口初始化、中断初始化等-Exercise program, based on the the xs128 core LED flashes for the Freescale novices practice. Basic initialization initialization clock port initialization, interrupt initialization