搜索资源列表
FFT v1
- IP core fft verilog code example
MAKEAMIF
- 用于生成xilinx开发环境中存储器ip core的mif数据文件的程序代码。(this program is used to generate mif file used by xilinx memory ip core.)
MAKEXCOE
- 用于生成xilinx开发环境中存储器ip core的coe数据文件的程序代码。(this program is used to generate coe file used by xilinx memory ip core.)
divider
- a vhdl code for divide operation in fpga spartan6
06_pll_test
- 锁相环IP核的使用，包括详细的配置，适合学习使用；(The use of PLL IP core, including detailed configuration, suitable for learning to use;)
10_rom_test
- rom ip核的配置，以及测试文件，适合初学者使用。(ROM IP core configuration, as well as test files, suitable for beginners to use.)
ethernet_loopback
- 通过FPGA驱动千兆以太网口，完成SPARTAN6上的UDP数据包闭环测试，即通过网口发送数据包到FPGA，FPGA内部将接收到的数据返回到PC机，建议测试之前添加ARP静态绑定，FGPA内部的IP以及MAC地址在ROM里的COE文档里可以看到，发送端添加了CRC以及整体CHECKSUM的计算(Driven by FPGA Gigabit Ethernet port, UDP SPARTAN6 data packet on the closed loop test, through the ne
parallel_norflash_test
- ISE工程，并行nor flash的读、写、擦出，其中有个调用FIFO16-16的IP核，已经在工程中(ISE engineering, parallel nor FLASH read, write, erase, where there is a call FIFO16-16 IP core, has been in the project)
XILINX_DDR3_IP核使用教程
- 详细介绍了Xilinx DDR3 IP核的使用方法和注意事项(The usage and attention of Xilinx DDR3 IP core are introduced in detai)
rocetech- 加密方法
- FPGA加密主要有 1.配合第三方加密芯片（如ds180等，通过控制程序复位使能实现） 2.自带加密逻辑硬核(如5/6/7系列中的BbRAM和eFUSE存储密钥实现) 主要讲述一下如何用自带的IP进行加密逻辑。(FPGA encryption mainly 1. With third-party encryption chip (such as ds180, etc., reset by controlling the program to enable) 2. Comes with
cpu_uart_leds_ip
- 基于Altera 的一个IP核，能完成串口收发,以及自定义IP,可以作为自定义AXI总线接口的例子(Based on Altera's IP core, to complete the serial transceiver, as well as custom IP, as a custom AXI bus interface example)
Wavemaster_W5300
- 用FPGA语言，基于W5300芯片实现TCP/IP协议的网络传输，将W5300部分程序实现IP封装，只有输入输出管脚和时钟，复位等管脚(FPGA language is used to realize the network transmission of TCP/IP protocol based on W5300 chip. The W5300 part of the program realizes IP packaging, and only the input and output p
LaSaNewNB_M88E1111_TCP1000mhz
- 用FPGA，基于M88E1111芯片实现的TCP/IP协议的千兆网，将协议封装成IP核(With the FPGA, the TCP/IP protocol based on the M88E1111 chip is used to encapsulate the protocol into IP core)
imports
- 用FPGA实现UDP/IP协议，对于想用FPGA实现UDP/IP协议的可以看一看(Implementation of UDP/IP protocol with FPGA)
exp_fft_test_724
- 在quartus软件中调用FFT的IP核，编辑IP核的驱动模块，使得IP核读入数据进行处理，输出数据。使用modelsim进行联合仿真。(In the quartus software, the IP kernel of FFT is called, and the driver module of the IP kernel is edited, so that the IP kernel is read into the data for processing and output data
zcu102_exp_1
- 给予Xilinx系列zcu102开发板，完成了一个基本的project，实现了PS 端对PL 端的控制，并在PL端自己生成IP，是初学者很好的学习模板。(Xilinx series zcu102 development board, completed a basic project, the PS end to the PL control, and the PL end of the generation of IP, is a good learning template for begi
xapp794
- 里面分为八个实验，一步一步教你使用system genertor for dsp 生成能供vivado使用的IP核文件。(It is divided into eight experiments, which teach you to use system genertor for DSP step by step to generate IP core files that can be used for vivado.)
FIR设计实现sgh
- FIR滤波FPGA实现 ，已在仿真软件上验证实现，不是IP核，不是ip核。(FIR filter FPGA implementation, has been verified in the simulation software, not IP core, not IP core.)
sobel
- 由Verilog编写在FPGA实现sobel算法应用于图像边缘检测，工程文件可在quartus13.1以上版本打开；工程使用到ram、fifo、pll三种ip核，design文件夹下包含ram、fifo、vga控制以及串口收发和sobel算法模块，sim和doc文件夹下分别包含modelsim的仿真模块和仿真结果；测试时将200*200分辨率的图片用matlab文件夹下的matlab脚本压缩、二值化，再将生成文件中数据用串口发给FPGA，边缘检测结果会通过VGA输出。(Written by Ve
ethernet_ip_verilog
- 以太网的ip,用verilog写的，包含testbench,用于FPGA以太网设计参考