搜索资源列表
miaobiao
- 计数秒表能运用于各种计数方面,可以从0到59计数-Count the stopwatch can be used in a variety of counts can be, you can count from 0-59
miaobiao
- 单片机做的高精度的秒表用C语言和汇编语言编的程序,数码管显示秒表值-SCM do of high accuracy of the stopwatch C language and assembly language compiled program, digital pipe display a stopwatch value
miaobiao
- 基于msp430的秒表设计,带1602显示功能-Based on msp430 stopwatch design, with 1602 show function...
miaobiao
- 秒表计时功能,可以从零记到九十九,可以暂停,可以清零。-Stopwatch functions, from zero in mind to 99, you can pause, can be cleared.
miaobiao
- 秒表设计,用于在液晶lcd上显示秒表,有计数和暂停功能-Stopwatch design, for display on the LCD lcd stopwatch, count and pause functions
miaobiao
- 基于stc89c52单片机用C语言写成秒表-Stopwatch stc89c52 microcontroller written in C
miaobiao
- 通过51单片机来实现秒表的功能。封装程序,立马可以使用-51 single-chip to achieve the function of the stopwatch. Package program can immediately use
miaobiao
- 秒表程序,最多走一小时,chuli()函数里可以看出来,百位用了另一个数组,目的是显示小数点,前两位是分钟,后两位是秒,小数点只是为了区分秒和分,没什么特殊的意义,这不是程序的重点,你要的暂停和开始是同一个键,我用的是两个,你可以自己-Stopwatch program, up to go, chuli () function can be seen, one hundred with another array, the purpose is to display the decimal po
miaobiao
- 在FPGA上编写了一个秒表运行程序,包括六位显示,其中包括时,分,秒,分别都是两位显示-In FPGA to write a stopwatch to run the program, including six display, including, points, second, respectively are two display
miaobiao
- 秒表的单片机完整电路与程序,已经测试通过。-Stopwatch microcontroller complete circuit and procedures, has been tested.
miaobiao
- 用中断控制的简易秒表 摁一下开始,摁一下暂停,再摁一下清零,依次循环 -A simple stopwatch interrupt control press start, press again to pause, then press about cleared, followed by cycle
miaobiao
- 用按键控制秒表的启动暂停和清零。秒表的时间范围为00.0-59.9-With key control the stopwatch start pause and cleared. Stopwatch time range of 00.0-59.9
51-miaobiao
- 51单片机实现秒表,对于希望通过51做小东西的朋友,可以试试,并通过注释修改代码,实现想要的功能。-51 SCM realizing stopwatch, to hope that through 51 do little friend, can have a try, and through the comments modified code, and realize the function of want
miaobiao
- 秒表的VHDL语言程序,是实验课上一个课程设计,非常正确,非常好用。-Stopwatch VHDL language program is the experimental class curriculum design, very correct, very easy to use.
miaobiao
- 使用单片机、液晶显示器、两个按键(确定键、功能键)及其它外围元件,设计一个秒表,实现功能如下: (1)开机上电后,液晶显示器第一行显示“Welcome Here!”,第二行显示“Please Enter Key”。 (2)按下“确定键”,液晶显示器先清除屏幕,然后再显示,第一行显示你的姓名拼音,第二行显示你的学号。 (3)按下“确定键”后,液晶显示器先清除屏幕,然后进入到秒表的界面,第一行显示“Miao Biao Test”,第二行显示“00.00”,计时到秒后面两位。 (4)第
miaobiao
- 它具有计时功能。此秒表有两个按键(reset, start)按下reset键后,秒表清零,按下start键后,开始计时,再次按下start键后, 暂停计时,秒表显示内容闪烁。 用FPGA开发板上的两个七段数码管显示时间(以秒为单位),计时由0 到 59 循环。-It has a timer function. This stopwatch has two buttons (reset, start) reset button is pressed, the stopwatch is clear
miaobiao
- 本系统中可以实现“启动/停止”、“清零”等功能。LED数据端口使用的是P0口,由于采用了共阴数码管,且面包板上空间有限,未加扩流三极管,只使用了上拉电阻。为使电路工作更加稳定,加了上电复位电路。 -" Start/stop" , " clear" function can be achieved in the system. LED data port P0 port common cathode due to the digital control and
miaobiao
- 在keil环境下,用C语言实现最大计数为10分钟的秒表功能,-Maximum count for a 10-minute stopwatch function in keil environment using C language
miaobiao
- verilog 的 48M频 出入秒表,带停止启动 清零功能-the verilog of 48M frequency of access stopwatch, with stop start clearing the
miaobiao
- 基于89c51单片机开发的简易秒表程序 是用汇编语言编写的-Based on the 89c51 microcontroller developed simple stopwatch program is written in assembly language