搜索资源列表
fc
- 用c语言编写的飞控主程序 实现三轴加速度与陀螺仪的稳定控制 -fly control
3
- stm32做的 mti陀螺仪的读数及运用程序 mdk的环境 红牛的板子-stm32 do mti gyro readings and use program environment mdk Red Bull board
kalman
- kalman滤波 加 小波阀门滤波法 该文为陀螺仪滤波程序-kalman filter
kamaanguji
- 卡尔曼 陀螺仪、倾角传感器融合,主要用了自适应卡尔曼滤波-Kalman gyro, tilt sensor fusion, the main use of the adaptive Kalman filter
ISY300AL
- 爱普生陀螺仪资料的应用手册与开发功能使用注意-Epson gyroscope application of information and development of functional use of manual attention
Gyro
- 陀螺仪加单码盘, 用单片机积分实现机器人全场定位 -Gyro and single plus encoder robot positioning
Strapdown
- 一、数据说明: 1:惯导系统为指北方位的捷连系统。初始经度为116.344695283度、纬度为39.975172度,高度h为30米。 初速度为v0=[0.000048637 0.000206947 0.007106781],飞行高度不变。 2:jlfw中为600秒的数据,陀螺仪和加速度计采样周期分别为为1/80秒和1/80秒。 3:初始姿态角为[0.120992605 0.010445947 91.637207](俯仰,横滚,航向,单位为度), jlfw中保存的为比力信
AVRC
- 在linux下调试 陀螺仪 和 加速度传感器 参数设置,里面的文件已调试好 可已在 AVR Gcc下直接运行-Under the debugger in linux gyroscope and acceleration sensor parameter setting, which the document has a good debugging AVR Gcc may have been under the direct operation
test_idg300
- Arduino测试idg300,读取idg300的陀螺仪信号,并且通过串口监视器显示出来。要求将传感器的输入端连接到单片机的2号模拟输入端。-Arduino—test-idg300
L3G4200_1602_SPI
- 意法半导体公司推出的三轴陀螺仪+温度传感器L3G4200 SPI驱动-STMicroelectronics has introduced a three-axis gyro sensor L3G4200 SPI driver+
HORIZON
- 陀螺仪材料,自动控制不可缺少的 对于其使用还需各位多多指点啊-Gyroscopes material, automatic control indispensable need for their use that a lot of pointing ah
Timers2-6.6
- 基于陀螺仪原理的惯性导航程序 用于测量量角速度-Based on the principle of gyroscope inertial navigation procedures used to measure the amount of angular velocity
somegrp
- 几篇陀螺仪的有用的文章, 几篇陀螺仪的有用的文章-Gyroscopes several useful articles, a few useful gyroscope article
213
- 陀螺仪漂移特性的小波分析 陀螺仪漂移特性的小波分析-Gyroscope drift characteristics of the wavelet analysis of the characteristics of gyroscope drift gyroscopes drift wavelet analysis Wavelet analysis
1231315
- 动力调谐陀螺仪误差及其补偿算法的研究 动力调谐陀螺仪误差及其补偿算法的研究-DTG error compensation algorithm and its DTG error compensation algorithm and its
796e50c2-1775-4730-8213-2225004ca5c1
- 利用matlab数值计算的强大功能和,建模容易实现的特点"进行了捷联式惯性导航系统的仿真研究,对四元数及姿态矩阵等的解算采用编程实现"陀螺仪和加速计的建模用.-Matlab numerical calculation using the power and, modeling the characteristics of easy to implement " a strapdown inertial navigation system of the simulation study a
IDG500
- 最新IDG500陀螺仪的芯片资料,陀螺仪-IDG500
LYPR540AH
- 意法半导体公司才推出的三轴陀螺仪,同时输出三个轴的模拟信息量,而且有2种数据格式。-STMicroelectronics was introduced three-axis gyroscope, while the analog output three-axis the amount of information, but there are two kinds of data format.
ogl_vertex_array_range
- 此为关于陀螺仪的一个MATLAB程序。经过仿真得到陀螺仪的运动状况-This is on a MATLAB program gyroscope. The simulation to be the movement of gyroscope
tuoluoti
- 哈工大的陀螺仪原理,讲述了微机械陀螺仪,挠性陀螺,激光陀螺等!-HIT gyroscope principle described micromachined gyroscope, flexible gyro and laser gyro and so on!