搜索资源列表
NXPsoftwareUARTforLPC2000
- NXP公司写的模拟串口程序,功能全面,很强大-NXP' s serial port to write the simulation program, full-featured, very powerful
msp430shujucaijixitong
- msp430f149实现的数据采集系统 结构简单 功耗低 模拟采集传感器 数字开关量采集 串口通讯UART模块 电源供电及复位-Executable files built outside of IAR Embedded Workbench Follow these steps to load and debug an executable file that was built outside IAR Embedded Workbench, for example p
SuperComm
- 电子工程师或软件工程师开发设计串口界面的时候,经常需要模拟软件(仿真软件)或协议分析仪对串口通讯进行监控模拟。有了串口通讯软件SuperComm,工作方便多了。不再需要昂贵的协议分析仪,不再需要专门编写仿真软件,只要一台运行微软Windows 2000/XP的电脑加上SuperComm,稍加配置就可进行开发测试了。 -Electronics engineers or software engineers developing and designing serial interface, it
11714318751IO_SOFT_UART
- 基于89S51的IO口模拟串口通信,调试通过。-89S51-based simulation of the IO port serial communication, debugging through.
m_usart
- PIC单片机模拟串口收发.可设置波特率。8位9位可选-PIC microcontroller analog serial transceiver. You can set the baud rate. 8 9 optional
mcu_51_io_uart
- 51单片机IO口模拟串口通讯C源程,适用于AT89S51/AT89S52等单片机。-MCU GPIO uart c source code ,can use for AT89S51/AT89S52 etc.
bright
- PIC16c57 Bright embedded control module模拟串口通信部分-PIC16c57 Bright embedded control module
PLCWork
- 一台电脑上,没有实际的串口设备,只需要安装虚拟串口,再用这段小程序,就可以对电脑VBA程序进行调试了。 这段程序实际上是在一个专门的ExcelVBA文件模块里,模拟外设,与主程序ExcelVBA进行呼应。-A computer, there is no real serial device, only need to install a virtual serial port, and then this little program, you can debug a computer pr
adcmeter
- 基于 CS5550 工业测量仪表的设计:ADCMeter.ddb 中包含电路原理图和样品PCB图。本系统以 STC 系列 51 单片机为控制核心,使用高精度 CS5550 A/D 芯片来采集微弱的模拟信号量(如热电偶,热电阻信号量),可在线校准(零校准,满量程校准),校准数据保存到 93C46 中,作为以后 CS5550 运行的校准参数。本系统还包括两行八个数字位的数码管实时地显示采集数据,并可通过板上按键输入,进行输入信号变换的切换。另外还可增加串口通信部分,将采集的数据传输给上位机或其它控制
moniUART
- 相当稳定的模拟串口程序,大家可以试试,解决了串口不够用的烦恼.-Fairly stable analog serial process, we can try to solve the serial port is not enough trouble.
51_int0_uart
- 利用51单片机的中断模拟串口,全部源码。直接用KEIL打开就可以了。-51 MCU interrupt simulation using serial, full source code. KEIL open directly on it.
SampleAppSlave
- CC2430的A/D转换测试程序。程序基于IAR软件编写的。通过A/D通道采集模拟量并转化为数字信号,然后通过串口发送到PC,在PC机可以看到采样结果。估计对开发无线传感器网络的相关人士比较重要-the A/D converter test procedure. Procedures prepared based on the IAR software. Through the A/D channel analog acquisition and digital signal
AD3
- MSP430单片机实现模拟量采集 通过串口上传给上位机-ADC12
VC-Serial-PC-simple-routines
- 该实例是用于vc环境下的通讯,即串口通信,很好的模拟了人的通讯功能,是研发者的参考资料-This instance is used for communication vc environment, that serial communication, a good simulation of human communication, is a reference for developers
VGPS
- 通过串口模拟GPS的程序,用鼠标相对于屏幕中心位置的偏移来模拟移动速度。-GPS through the serial port simulation program, with the mouse position relative to the center of the screen to simulate the speed of the offset.
uart
- HOLTEK单片机模拟串口编程的实现。了解串口通信的真正原理和过程!-HOLTEK analog microcontroller serial programming implementation. Understand the true principles of serial communication and the process!
Wave_Genert
- 这是一个串口接收数据 模拟生成波形的上位机程序 在下位机生成波形的模拟数据 通过AD转换为数字信号 传输给上位机 上位机显示出波形-This is a serial port to receive data simulation program generated PC wave machine generates the next bit analog waveform data is converted to digital signals by AD transmitted to the
DAC_demo
- 利用MSP430的通用IO模拟串口发送与接收数据。-Universal IO simulation using the MSP430 serial port to send and receive data.
IO模拟串口
- 以51 系列单片机为基础的普通IO模拟串口通信驱动程序
模拟串口与SYN6288通信
- 模拟串口与SYN6288通信,已通过测试,可以使用