搜索资源列表
UART
- 此程序是用msp430g2553通过串口与上位机通信，-This program is to communicate with the host computer through the serial port using msp430g2553
comm
- 通过串口实现上位机与下位机的通信。通过VC++编程软件控制电机转速、方向。位置。-Achieved through the serial port of the host computer and the next bit machine communication. Through VC++ programming software to control the motor speed and direction. Position.
TestSeriport
- 利用串口让上位机与android设备通过串口进行读写通信-Using the serial port to the host computer and android devices to read and write through the serial port communication
MCU51
- 51单片机通过串口通上位机通信，和上一个贪吃蛇是一个配套程序-51 microcontroller through the serial port via PC communications, and on a Snake is a companion program
vc_arm
- ESC打印机命令集 对打印开发有帮助串口调试工具，如何使用串口通信。串口编程:上位机源码-, how to use serial communication. Serial Programming
51Serial
- 51单片机AT89C52串行通信.上位机通过串口向单片机发数据，单片机接收后发回给上位机。-51 AT89C52 single-chip serial communication. PC send data through the serial port to the microcontroller, the microcontroller has sent back to the host computer.
fishTran3
- 基于stm32开发的仿生鱼控制程序，串口与上位机通信部分-Stm32 development of bionic fish based control program, serial communication with the host computer parts
VDIInit
- dsPIC30F3014 主要是通过spi控制adc 和dac.通过串口和上位机通信,用在监控上面.-dsPIC30F3014 is mainly controlled by spi adc and dac. through the serial port and PC communication, used in monitoring the above.
Proteus-virtual-serial-debugging
- 单片机的输入输出控制中，一般都通过串口和上位机PC进行通信.由于PC机拥有强大的数据处理功能以及友好的控制界面并且能实现远程控制所以显得尤为有用,此系统可以由上位机控制，通过串口操作单片机模块实现其相应功能。-Microcontroller input-output control, and generally communicate through the serial port and PC PC. Since the PC has a powerful data processing ca
xwj
- 可以进行温度、湿度的采集，并通过串口与上位机进行通信-Can collect temperature, humidity, and through the serial port to communicate with the host computer
VB串口程序
- 该程序包是针对VB与单片机的通信，用于上位机开发的程序，主要是VB开发。
UART_Rolling
- Atmega128UART串口与上位机通信的程序，开发环境为gccavr。可接收发送字符串。接收上位机发来的字符串时，以字符 0 表示字符串的结束。-Atmega128UART serial communication with the host computer program, you can receive send strings. When receiving a string sent to the host computer to the characters ' 0'
UART_Interrupt
- Atmega128UART串口和上位机通信程序，采用中断方式实现。从上位机接收数据时，以字符 0 表示字符串的结束。开发环境：GCCAVR。-Atmega128UART serial port and PC communication program, using interrupts ways. When receiving data from the host computer to the characters ' 0' indicates the end of the st
EP100BT
- 这是关于EP100的bootloader,并且自己设计了一个基于VB的串口的上位机，使用串口通信，进行程序升级。-It is about bootloader of EP100
MMA7455
- 利用CC2530实现IIC总线通信协议采集三轴传感器MMA7455数据，读取MMA7455的数据，并通过口串口在上位机显示 -Use CC2530 implement IIC bus communication protocol data acquisition triaxial sensor MMA7455, MMA7455 read data through the serial port on the PC display
MSP430F5529-CC2650-74
- 采用超低功耗处理器MSP430实现串口与上位机MCU的通信-MSP430 ultra-low-power processor to communicate with the serial port of the host computer MCU
LightText02
- OPT光源控制器串口通信程序，通过串口将上位机数据发送给光源控制器控制光源亮度。-OPT light source controller serial communication program, the host computer through the serial port to send data to the light source controller controls the light source brightness.
串行口通信程序
- 基于modbus协议的上位机和单片机串行通信的程序(serial communication between PC and microcontroller program based on Modbus protocol)
USART_int(20170429)_OK
- 下位机传感器节点通过相应的协议和上位机进行通信(The sensor node communicates with the host computer through the corresponding protocol)
数据帧写入
- 针对某款气密性设备开发的上位机，利用串口实现通信。(According to the upper computer developed for a kind of air tightness equipment, the communication is realized by serial port.)