搜索资源列表
HONGWAI
- 红外测试程序，用单片机通过发射管发射38K的调制频率码，由一体化接收并解码由发光管显示。*正常情况下，由于反射和高灵敏度接收，LED4（P1.3)一直闪烁，可以用黑色纸片完全遮挡接收头使*之不能接收到发射管的信号，这是LED4熄灭。说明功能性正常-Infrared testing program, microcontroller through the launch tube with a 38K code modulation frequency, from integration to re
HONGWAIII
- 红外测试程序，用单片机通过发射管发射38K的调制频率码，由一体化接收并解码由发光管显示。*正常情况下，由于反射和高灵敏度接收，LED4（P1.3)一直闪烁，可以用黑色纸片完全遮挡接收头使之不能接收到发射管的信号，这是LED4熄灭。说明功能性正常-Infrared testing program, microcontroller through the launch tube with a 38K code modulation frequency, from integration to rec
hongwaijiema
- STC90C51单片机扩展功能，C语言编写，红外解码实验，红外发射和接收。-STC90C51 SCM extensions, C language, decoding experimental infrared, infrared transmitter and receiver.
main
- 基于stc89c52单片机的红外发射程序。-Microcontroller based stc89c52 infrared emission process.
hongwaibianma
- NEC标准的红外编码程序，用单片机和一红外发射二极管能实现遥控板的功能，对应的还有红外解码程序，稍后找找上传-NEC infrared coding standard procedures, using infrared emitting diode chip and a remote control board to achieve the function, along with the corresponding infrared decoding process, look for la
34324
- 红外发射程序 用的KEIL 4开发环境！用的STC 51 系列单片机-Infrared emission with the KEIL 4 program development environment! With the STC 51 Series MCU
keil-hongwai-jiema
- 单片机红外遥控小车程序，包括发射和接收程序，不错-progress of mcu
AT89C51
- 单片机红外遥控解码。红外遥控发射芯片采用PPM编码方式,当发射器按键按下后,将发射一组108ms的编码脉冲。遥控编码脉冲由前导码、8位用户码、8位用户码的反码、8位操作码以及8位操作码的反码组成。 -SCM infrared remote control decoding. Infrared remote control launch chip adopt PPM coding way, when transmitters keys pressed, will launch a group
hw
- 单片机红外通信实验，实现发射与接收解码的功能-Microcontroller infrared communication experiment, the transmitter and receiver decoding function
single-chip-infrared-decoding
- 51单片机红外遥控解码 红外遥控发射芯片采用PPM编码方式,当发射器按键按下后,将发射一组108ms的编码脉冲。遥控编码脉冲由前导码、8位用户码、8位用户码的反码、8位操作码以及8位操作码的反码组成。通过对用户码的检验，每个遥控器只能控制一个设备动作，这样可以有效地防止多个设备之间的干扰。编码后面还要有编码的反码，用来检验编码接收的正确性，防止误操作，增强系统的可靠性。前导码是一个遥控码的起始部分，由一个9ms的低电平(起始码)和一个4. 5ms的高电平(结果码)组成，作为接受数据的准
39Infra-red
- 红外测试程序，用单片机通过发射管发射38K的调制频率码，由一体化接收并解码由发光管显示。-Infrared testing procedures, microcontroller through the firing of 38K code modulation frequency, from integration to receive and decode from the LED display.
IR
- 基于89C51单片机的红外发射接收程序，发射头是5MM的那种，接受头是HS0038，不要用1838，1838不明显。-Based on the 89 C51 infrared emission receiving procedures, 5 MM head is a launch that, accept the head is HS0038, don t use of 1838183 and not obvious.
Redcode_diode
- 该程序可以通过单片机控制一个红外发射二极管输出38kHz的波形，这个波形HS0038红外接收器可识别，这种方式可用于传输信号。-The program can be controlled through the microcontroller with an infrared emitting diode output 38kHz waveform, this waveform HS0038 infrared receiver can identify, in this way can be u
tx
- 单片机 红外 遥控 小车 发射 程序 好资料-IR wireless progress of small bus of MCU
Infrared-testing-procedures
- 红外测试程序，用单片机通过发射管发射38K的调制频率码，由一体化接收并解码由发光管显示-Infrared testing procedures, with MCU through the launch tube 38K modulation frequency code integration to receive and decode LED display
red-mcu
- 基于51单片机双红外发射壁障原理测试源程序-Based on 51 single-chip dual-infrared emission barrier principle test source
infrared-ray
- 名称：红外发送 接收 测试程序 内容，用单片机通过发射管发射38K的调制频率码，由一体化接收并解码由发光管显示。-Name: Infrared sending and receiving the test program content, launch tube with MCU 38K modulation frequency code integration to receive and decode LED display.
hongwaiOK
- 51单片机的红外发射与接收及其仿真，自己写的C语言代码-51 microcontroller infrared transmitter and receiver, and its simulation
xunjixiaoche
- 利用循迹信号采集模块中的红外发射接收对管检测路面上的轨迹 将轨迹信息送到fpga，fpga将轨迹信息通过led灯显示出来，在通过fpga发轨迹信号给单片机，通过单片机来控制电机的转动。同时单片机将小车的状态反馈给fpga，fpga通过1602液晶显示小车的状态。-Infrared tracking signal acquisition module transmitting and receiving tube detection on the road trajectory to the
remote_c51
- 本文重点介绍了利用单片机AT89C51和AT89C2051实现红外发射和接收电路的设计方法。发射电路采用单片机89C2051将待发送的二进制信号编码调制为40KHz的脉冲信号通过红外发射管发射红外信号。红外接收端采用一体化红外接收头HS0038接收红外接收信号。-This article focuses on the use of SCM AT89C51 AT89C2051 achieve infrared transmitter and receiver circuit design. Tra