搜索资源列表
timer-LED
- 单片机C51 使用定时器延时,数码管的流动显示-Timer LED
LED-lights-timer-control
- 用定时器来控制LED灯的亮灭,定时器溢出时便产生中断,控制LED亮灭。-LED lights with timers to control the light off, the timer generates an interrupt when it overflows, control LED light off.
8alarm-led
- atmel\at89x51 数码管显示,I2C,定时器中断,8个闹钟 -atmel\at89x51 ,LED,I2C,T0 interrupt,8alarms
LED-flash-timer--cc2430
- 物联网必学芯片:cc2430 实验例程:利用定时器实现LED闪烁 虽然源程序可以用VC打开,但工程的开发环境应为IAR Embedded Workbench-Things will learn chips: cc2430 experimental routine: use timer, LED flash can be used although the VC open source, but the engineering development environment should
led-light
- 点亮小灯的各种方式,有定时器计数器。有模拟交通灯程序,-Light a small light in various ways, there is the timer counter. A simulation program traffic lights
PWM
- 内容:1、利用定时器产生PWM,了解原理和使用方法 2、硬件要求:LED灯 定时器 3、试验现象:LED灯由亮到灭,由灭到亮逐步变化,也就是调光现象-: 1, using the timer generates PWM, understand the principle and the use of method 2, the hardware requirements: LED light timer 3, the test phenomenon: LED light from b
PWM-control-of-LED-light-and-dark
- PWM控制LED亮暗 // 利用定时器控制产生占空比可变的 PWM 波 // PWM值增加,则占空比减小,LED 灯渐暗。 // PWM值减小,则占空比增加,LED 灯渐亮。 -PWM control of LED light and dark// use timer control variable duty cycle PWM wave generated// PWM value increases, the duty cycle is reduced, LED lights
EX02_CpuTimer2
- DSP2812定时器LED验证显示源程序,LED会奇偶数交替闪烁-DSP2812 timer LED display source code verification, LED will flash alternately odd number
LED
- 单片机定时器控制LED灯的闪烁,能帮助学习定时器的应用-Single-chip timer controls the LED lights flash, application of the timer can help learning
led
- 有关流水灯的不同的变化的程序,1)间隔300ms先奇数亮再偶数亮, 循环三次;一个灯上下循环三次; 两个分别从两边往中间流动三次; 再从中间往两边流动三次;8个全部闪烁3次; 关闭发光管,程序停止。 2)上下下上两次,全熄全亮五次 3)演示8位二进制数累加过程 4)依次亮一下 5)流水灯+蜂鸣 6)流水灯+定时器-Different light on the changes in water programs, 1) interval of 300ms the
led
- 时钟定时器C语言源代码。用于DSP和各种仿真软件。-Clock timer c language code
8253control-the--LED
- 设计基于Intel8253的定时器,设计一个电路,使8个指示灯依次闪动,闪动频率为1Hz。- design based on the Intel8253 timer, design a circuit, that eight in turn indicator lights flashing, flashing frequency for 1 Hz.
LED-or-Relay-controlling
- 利用51C单片机C语言编程,利用定时器定时控制继电器或其他输出控制,用数码管显示时间。- Use of 51 single-chip microcomputer C C programming language, using the timer timing control relay or other output control, with a digital tube show time.
Atmega16-LED
- Atmega16的LED灯闪烁程序,基于定时器的哦。-Atmega16 LED flashing procedure, based on the timer!
led
- STM32F4xx系列单片机编程模版,内涵systick定时器编程-STM32F4xx series microcontroller programming templates, the connotation systick timer programming
led
- 此程序为51单片机,4 只LED 在定时器控制下滚动闪烁。-This program for 51 single-chip, four scroll flashing LED in the timer control.
PWM-control-LED-more
- 单片机定时器产生一个PWM波,控制LED灯的亮灭程度。-Microcontroller timer generates a PWM wave to control the degree of bright LED lights off.
LED
- 复杂的数码管动态显示和流水灯,分别用两个定时器做中断-Complex digital dynamic display and light water, respectively, two timers interrupt
LED
- 主要功能和技术指标要求: 1. LED灯外接于P0.0端。 2. LED灯分别按2Hz,1Hz和0.5Hz三种不同频率闪动,各持续10s。 3. 在LED灯开始和停止闪烁时蜂鸣器分别鸣响1次。 4. 利用单片机内部定时器定时,要求采用中断方式 -The main features and technical requirements: 1 LED lights external P0.0 end. 2. LED lights press 2Hz flashing 1Hz an
利用C8051F310单片机设计一个LED灯控制器
- 实验目的:加深对定时/计数器、中断、IO端口的理解,掌握定时/计数器、中断的应用编程技术及中断程序的调试方法。 实验内容:利用C8051F310单片机设计一个LED灯控制器 主要功能和技术指标要求: 1. LED灯外接于P0.0端。 2. LED灯分别按2Hz,1Hz和0.5Hz三种不同频率闪动,各持续10s。 3. 在LED灯开始和停止闪烁时蜂鸣器分别鸣响1次。 4. 利用单片机内部定时器定时,要求采用中断方式。 提高要求: 使用按键(KINT