搜索资源列表
Switch-test
- 开关量测试程序 硬件: AT89S52 STC89C52 开关量输出传感器 说明: LED显示传感器状态 -The test program hardware switch: AT89S52 STC89C52 switch output sensor Descr iption: LED display sensor status
zhinrng
- 只能控制器,是一宗只能控制设备,可以控制开关量定时,开为2s,关为2s,共3组-The only controller, one can only control device, can control the switch timing, open for 2s off for 2s 3 groups
labview-0
- 工业开关量检测模块的原代码,三菱plc与pc通信的一个很好的例子-Industrial switch detection module source code, Mitsubishi plc and pc communication a good example
PC_Visual-CPP_IO_I_PPI
- PC_Visual C++通过PPI协议实现开关量输入 PLC段无需编程-PC_Visual C++ PPI protocol switch input PLC segment without programming
PC_Visual-CPP_V_ZiYou_PPI
- PC_Visual C++通过自由口实现电压开关量输入-PC_Visual C++ free port voltage switch input
PC_Visual-CPP_IO_O_PPI
- PC_Visual C++通过PPI协议实现开关量输出PLC段无需编程-PC_Visual C++ PPI protocol switch output PLC segment without programming
pic18
- ● C语言程序例程。该子目录包括以下子程序: ——AD程序实现模拟量到数字量的转换功能; ——CAN程序实现CAN总线通讯功能; ——keyboard_check程序实现键盘的扫描查询方式输入; ——keyboard_disturb程序实现PORTB的"电平变化中断"进行键盘的输入; ——led0-8程序实现在8个LED上依次显示1~8数字; ——PWM程序用于使CCP1模块产生分辨率为10位的PWM波形,占空比为50 ; ——RS-232程序通过RS-232接口来完
CAN-analog-input-and-switch-output
- 基于CAN的模拟量输入与开关量输出,程序正常运行的条件: 1、安装板卡,连接模块; 2、安装板卡驱动程序。-CAN analog input and switch output, the program normal operation conditions: 1, mounting board connection module 2, install the board driver.
IO_AD
- 任务1:编写程序,从PA口输入开关量,由PB口输出,通过发光二极管指示其状态。 任务2:由电位器电路板分压获得模拟信号,输入到ADC0809的IN0通道,编写程序,将得到的AD转换结果保存到内部RAM中。-Task 1: programming, input from the PA port switch by PB output by light-emitting diodes indicate their status. Task 2: by the po
MQ4
- 基于51单片机烟感报警程序,采用的是MQ4的气体检测传感器,开关量输出,检测后报警-Based on the 51 MCU smoke alarm program, using a MQ4 gas detection sensor switch output, after the alarm detection
URM37-ultrasonic-sensor.c
- 使用URM37的超声波传感模块进行开关量的串口通信-URM37 ultrasonic sensing module switch serial communication
8255
- 微机实验8255 1)用8个LED来反映8个开关量的状态,拨动开关,让对应的灯亮。 2)8255控制交通灯 本设计用LED来模拟交通灯。请考虑8255与LED的连接,以及如何用8255来控制LED的点亮与熄灭。 交通灯的控制过程: 东西向的绿灯、南北向的红灯亮5秒钟。 东西向的绿灯灭、南北向的红灯亮,在此时间段中东西向的黄灯闪烁5次,每次亮0.5秒灭0.5秒。 南北向的绿灯、东西向的红灯亮5秒钟。 南北向的绿灯灭、东西向的红灯亮,在此时间段中南北向的黄灯闪烁5次,
DI(LabVIEW6i)
- 基于研华数据采集的开关量输入程序,对于学习研华板卡的人来说很有用,-Advantech-based data acquisition switch input program, useful for people learning Advantech board
data-signal-gather
- 实现了两种开关量采集方法,C语言,源码,实用,可直接用于工程项目,有比较,有分析!-Two kinds of switch acquisition method, C language source code, utility, can be used directly for the project, compared to some analysts!
DIO
- 开关量卡通信例子,两台电脑之间用线将开关量卡连接上,可以用输入输出读取写入开关量卡-The switch card communication example, between the two computers with a line connected to the switch card on the card can read write input and output switch
fx1n
- 梯形图需要用PWM格式(用FXGPWIN编写就可以),CPU型号要选FX-1N,支持的指令不多,开关量还是可以的,老版了,不过是破解版不要钱。-Written in FXGPWIN ladder need to use PWM format (can be), the CPU model to choose the FX-1N support the instruction of not more than, the switch can still, old version, but not
8051_MODBUS_RTU
- 用STC89C58单片机做的数据采集和控制,12位AD转换使用TLC2543,通讯协议采用MODBUS(RTU),通过拨码开关改变从机地址,支持模拟量或数字量的读写。(4路模拟量输入、6路开关量输出(继电器输出)、8路开关量输入).-To do STC89C58 SCM data acquisition and control, 12 AD converter TLC2543, communication protocol MODBUS (RTU), to change the slave ad
50462R51
- 用于红外解码器50462的解码,编码,串行口传输,并控制2个开关量输出。-Used for the the infrared decoder 50462 decoding, encoding, serial port transmission and control two switch output.
MCF52233-Switch
- 基于飞思卡尔单片机MCF52233的开关量控制函数的使用。仅供参考。-Based on the the Freescale microcontroller MCF52233 switch control the use of the function.For reference only.
paint
- 绘图软件,包括静态图形,例如直线,折线,椭圆,等。还包括动态元件的定义,例如模拟量和开关量(布尔值)。-Graph software