搜索资源列表
source
- 使用 STC12C5A60S2单片机的AD转换，采集电压信号，通过上位机查询命令上传相应的数据，同时可以保存到STC12C5A60S2的EEPROM中，作为离线采集器，-Use STC12C5A60S2 MCU AD converter, voltage signals collected by the host computer to upload the corresponding data query commands, and can be saved to the EEPROM of
dianzicheng
- 有两个数据包，包含单片机的程序和QT的程序，单片机采集物品的重量，然后将重量数据通过QT显示出来。qt界面可以显示单价等信息。有问题请联系：hellojinhongdu@126.com-There are two packets, including SCM procedures and QT procedures, singlechip to collect the weight of the goods, and then displays the weight data by QT. Th
guangzhao
- 采集光照数据并数显,只是基本程序。使用STC89C52单片机，四路光照采集，并经过AD转换后由8位串行数码管输出-Collecting data and digital light, just basic procedures. After using STC89C52 microcontroller, four light collection, and after AD conversion by the 8-bit serial digital output
STC89C52_PCF8591
- 使用keil4软件打开。源码中，通过单片机采集光敏电阻数据，以及超声波数据。得到当前环境的光照程度以及使用者离设备的距离，并且判断是否在有效的光线或者距离范围。给出声光指示，同时将数据发送到串口中。-Use the software to open keil4. The source, collection of photosensitive resistance data through the microcontroller, and ultrasonic data. Get the cur
60S2
- 基于51加强版单片机60S2，自带AD模块，可以直接单路多路采集数据，软件经过实际测试，保证可以用，12864显示-Based on an enhanced version of the microcontroller 51 60S2, built AD module, multi-channel direct single data acquisition, software after the actual test, can be assured, 12864
anlaysis_data_m_file
- 单片机采集到的车窗电压AD采样值，用MATLAB进行数据分析，电压变化曲线图像显示，以便进行模拟算法验证。-The car windows Voltage AD value from SCM AD-sampling collected, using MATLAB data analysis, image display voltage curves for simulation algorithm validation.
ke
- 基于单片机八路数据循环采集、ADC0809、89C52单片机-Microcontroller-based data acquisition cycle eight
STM32
- 基于STM32单片机将RS232串口采集的数据转换为CAN总线数据输出，程序中以采集电罗经数据为例，包括了电罗经数据的过滤、串口中断处理、CAN中断处理等程序模块。-STM32 microcontroller based data acquisition converts RS232 serial CAN bus data output, a program to collect electronic compass data, for example, includes a filter gy
ADTLC2543
- 利用51单片机控制tlc2543ad转换模块采集数据显示在数码管上。-Using 51 single-chip control tlc2543ad conversion data acquisition module in the digital tube display.
AD_TCL2543
- 单片机AD_TCL2543采集的数据在数码管上显示。-SCM AD_TCL2543 data collected on the digital display.
avr18b20
- ATmega8单片机读取DS18b20采集的多点温度，并在Nokia 5110液晶显示模块显示，且将数据发送到PC的串口终端显示-ATmega8 microcontroller reads DS18b20 multi-point temperature acquisition and Nokia 5110 LCD module display and send data to the PC s serial port terminal display
pressure_modbus
- 多个MSP430单片机采集气体压力，用RS485组网，采用MODBUS通信协议传输数据。-MSP430 MCU collecting multiple gas pressure, using an RS485 network, using MODBUS communication protocol to transfer data.
STM32-USARTS
- 基于STM32单片机的数据，多串口采集程序，本实例用来采集传感器数据-Based on STM32 MCU data of multiple serial port acquisition procedures, this example is used to collect sensor data
MCU_Pump
- 使用PIC单片机内部ADC采集，用串口回传数据给电脑-use PIC ADC UART TO PC
Lesson_DHT11
- DHT11温湿度传感器在AVR单片机中采集数据的应用。-DHT11 temperature and humidity sensor data acquisition applications in the AVR microcontroller.
com
- labview与单片机串口通信,采集数据显示并发送指令，实现监测。-labview serial communication with the microcontroller
STC1.SPI.ad1256
- 基于STC公司单片机的SPI协议，应用与AD1256的程序。最终将采集到的数据通过串口发送到上位机。-STC microcontroller based company SPI protocol, application procedures and AD1256. Eventually the collected data is sent to the host computer via the serial port.
ad.chuankou
- 基于STC51单片机的AD0804与AD0832程序，将模数采集到的数据发送到串口与上位机通讯。-Send STC51 based SCM AD0804 and AD0832 program, the modulus of the collected data to the serial port and PC communication.
ADDA
- 这是一篇关于单片机的ad或da怎么样采集数据，将模拟量转化成数字量的源程序。-This is an ad on the microcontroller or da how to collect data, the analog to digital conversion of the source.
RTGDSC
- 这是一个接收串口的数据，数据是通过单片机采集了温度光亮度数据传输到电脑串口上，这是一个服务端，接收了串口数据并存储到数据库，方便管理与使用-This is a receiving serial data, the data is collected by SCM optical brightness temperature data to the computer serial port, it is a server, receiving serial data and stored in t