搜索资源列表
voltage-and-current-data
- 支线分界开关实际运行的电压电流数据，3天-Line of demarcation switch voltage and current data of actual operation, the 3 day
xingboshiyan02
- 这是行波保护的程序，用于电力系统中行波保护的仿真建模，实现电压电流的波形可视化。-This is a traveling wave protection program, used for modeling and Simulation of traveling wave protection of power system, realize the visualization of voltage and current waveform.
Power
- 基于51单片机的数控电源的设计，里面设计用到的AD电压电流的采集，可以很好的学习和使用-Based on 51 single chip microcomputer numerical control power supply design, AD design used in voltage and current collection, can be very good to learn and use
51-Collect
- TLC2543采集十路电压电流和温度，并且在液晶屏1602上显示出来，485传输代码还没写好，目前可以正常使用-TLC2543 collect ten road voltage and current and temperature, and displayed on the LCD 1602, 485 have not written the code, you can use it
case30
- IEEE30节点标准测试系统，可用于进行输电网潮流计算，对输电网潮流计算方法进行验证，看所所求各节点电压电流与标准值是否一致。-IEEE30 node standard test system, can be used in the calculation of the grid current to the grid power flow calculation method for validation, see the desires are consistent with the val
powerbank_charge_test
- 支持同时检测四路USB电压电流侦测，并计算出功率，和充电容量，并用LCD12864显示出来。-Support for simultaneous detection of four USB voltage and current detection, and calculate the power, and the charging capacity and use LCD12864 display.
boostpiusui
- 基于MATLAB boost 电路 带有电压电流控制环-boost MATLAB
feeder13
- PSCAD 4.5 下的 IEEE13 节点模型搭建，绝笔好用！ 可以实时测量相角变化、电压电流、等信息。-This file is produced in PSCAD 4.5 IEEE13 model, which is good for use. You can get almost all information this model.
STM32-based-temperature-P-voltage
- STM32温度+电压电流(上位机显示好的)-STM32-based temperature+ voltage display (PC display)
xingbotiqu
- 提取三相交流系统输电线路的行波电压电流，进行故障分析-Extracted three-phase AC transmission line system line wave voltage and current, failure analysis
SG26K20-2014-5-10
- 电压电流热阻热偶信号源程序，是工程必备的-Voltage and current resistance thermocouple signal source is essential engineering
MPPT
- 太阳能光伏发电的电压电流曲线与电压功率曲线以及代码。-Solar photovoltaic voltage-current curve and voltage power curve and code.
CAP2
- 芯片类型STM32f103c8t6，模拟过零检测电压电流计算功率因数-Chip type STM32f103c8t6, simulate zero-crossing detection voltage and current to calculate the power factor
Gt_trans
- 求RMS，MATLAB中求正弦信号的电压电流的RMS-setting RMS，in MATLAB
pfc-boost
- 交错并联PFC boost，使用plecs仿真，仿真完美，电压电流环使用typeII补偿，CCM平均电流模式，额定功率500W，可根据需要改变参数-Interleaved PFC boost, use plecs simulation perfectly, voltage and current loop using typeII compensation, CCM average current mode, rated power 500W, parameters can be changed
shengjiangyaZHANBO
- 升压斩波电源设计，很好的仿真，准确电压电流控制-Boost chopper power supply design, very good simulation, accurate voltage current control
ele_bot
- boost 升压电路程序 蓝牙控制 可以使用手机蓝牙修改电压 电流等参数 使用STM8单片机 -boost boost circuit program can use the phone Bluetooth Bluetooth control modification
OLED
- OLED显示的数字电压电流功率容量表， 自己慢慢弄得，感觉还不做-OLED display digital voltage and current power capacity of the table, Slowly made their own, do not feel
USB
- OLED0.91显示的USB电压电流表程序，方便测试USB的电压电流情况-OLED 0.91 shows the USB voltage meter program to facilitate the test voltage and current situation of USB
power_hvdc_vsc
- 柔性直流输电仿真模型，及基于电压源的直流输电技术仿真。采用simulink编程，直观展示各级电压电流。-VOLTAGE SOURCE CONVERTER