搜索资源列表
PMSMEKF
- 介绍电机直接转矩控制系统，以及无传感器方面的研究-Introduce direct torque control system, and no sensor research
GJPMSM
- 讨论了新算法的应用，高阶直接转矩控制系统的建模与仿真-Discusses the application of the new algorithm, high-end direct torque control system modeling and simulation
DTC1
- 永磁同步电机基于空间矢量调制技术的直接转矩控制matlab仿真模型,-Technologies based on space vector modulation direct torque control matlab simulation model for PMSM
BLDC_DTC
- 基于永磁同步电机的直接转矩控制matlab模型-Based on permanent magnet synchronous motor direct torque control matlab model
dtc
- 根据博士论文搭建的永磁同步电机直接转矩控制matlab模型-According dissertation build permanent magnet synchronous motor direct torque control matlab model
feasiblePMSMdirectorqueccontrol
- 永磁同步电机直接转矩控制，经本人亲自测试过，确定可用-Permanent magnet synchronous motor direct torque control, as I personally tested, to determine the available
Direct-torque-vector-subdivision
- 针对永磁同步电机的传统直接转矩控制中的磁链和转矩脉动大的缺点,提出了十二扇区细分的磁链闭环控制方法和相应的电压开表。分析了电压矢量对电磁转矩和定子磁链的作用,得到有限的扇区和电压矢量会造成转矩和磁链脉动大。理论和实验对比分析了六扇区划分和十二扇区划分的控制性能。实验结果表明十二扇区划分的PMSM直接转矩控制方法,既保证了DTC的快速性,又很好地降低了转矩与磁链脉动。 -For the tradition of permanent magnet synchronous motor direct
Asynchronous_motor_subdivision
- 传统异步电机直接转矩控制多采用六边形磁链控制或六区间的圆形磁链控制，容易造 成转矩和磁链脉动过大，限制了其实用范围。针对此缺陷，本文采用矢量细分的方法，将传统的六电压矢量和六扇区细分为十二电压矢量和十二个扇区，制定了相应的矢量开关表，并通过 MATLAB 对其进行了仿真实验。仿真结果表明，基于矢量细分的异步电机直接转矩控制能够有效改善磁链轨迹，减小转矩脉动，提高系统控制性能。 -Conventional induction motor direct torque control multip
PMSM-DTC-start-figure
- 介绍了如何解决永磁同步电机直接转矩控制的启动问题-Describes how to troubleshoot permanent magnet synchronous motor direct torque control of startup problems
bldcdtc
- 文章介绍了永磁无刷直流电机的直接转矩控制，对电机控制学习人员来说是很好的资料。-This paper introduces the brushless DC motor direct torque control, motor control learning staff is very good information.
DTC
- 开关磁阻电机的直接转矩控制,传统的电压矢量选择方法-Switched reluctance motor direct torque control, the traditional voltage vector selection method
original_DTC
- 基于最简单的直接转矩控制的matlab程序框图，经试验，完全可以正常运转-Based on the most simple and direct torque control matlab block diagram, the test, can operate normally
DTCTCZ
- 永磁同步电动机的直接转矩控制仿真程序，可以直接运行-Permanent Magnet Synchronous Motor Direct Torque Control program, can be directly run
zhijiezhuanju
- 同步电机直接转矩控制的mdl控制 使用转矩和磁链给定 可以很好的跟踪给定值-Synchronous Motor Direct Torque Control mdl control the use of torque and flux can be a good track given setpoint
svpwmdtc
- 异步电机基于svpwm直接转矩控制的仿真模型-Svpwm induction motor direct torque control based on the simulation model
dtc3
- matlab simulink 仿真，异步电机的直接转矩控制，磁链为六边形磁链-matlab simulink simulation, asynchronous motor direct torque control, flux hexagonal flux
dtc
- 异步电机的直接转矩控制，磁链为六边形磁链，仿真环境为mtlab。-Asynchronous motor direct torque control, flux hexagonal flux, simulation environment is mtlab.
DTC_six
- 基于matlab/simulink的异步电机直接转矩控制，仿真运行正常。-Based on matlab/simulink asynchronous motor direct torque control, simulation run correctly.
DTC_yibudianji
- 绝对能走,异步电机直接转矩控制，用了好久才建出来，希望能对需要的朋友有所帮助-must run
DTCsix_torque
- 直接转矩控制（DTC）Matlab仿真文件-Direct Torque Control (DTC) Matlab simulation file