搜索资源列表
sensor0751212m
- 带霍尔位置传感器的直流无刷电动机控制-方波-Hall position sensor with brushless DC motor control- square
pspice_BLCDM_circuit
- 无刷直流电动机的电子电路硬件设计后,制作PCB版前,对电路进行的仿真-BLDCM hardware design of electronic circuits, the PCB version produced before the circuit simulation
zhiliudianji
- 本程序在单片机C8051F020上将直流电动机当前的转速值在七段数码管上显示出来,在电机的可控范围内控制电机转速等于预设值。运行速度设置为2000转/分,电机启动经过若干秒后,将以设定的速度运行。为了达到调速的效果,本程序使用阵列键盘更改运行速度。-This procedure will be in the single-chip C8051F020 DC motor speed value of the current Seven-Segment LED display out of cont
zhiliudiandongjidejixieeixing
- 直流电动机的机械特性,很有用的,MATLAB仿真-DC motor mechanical properties, very useful, MATLAB simulation
zhiliudianjiqidong
- 直流电动机的启动,MATLAB环境,对风机建模有帮助的-DC motor start-up, MATLAB environment modeling help fan
drive
- ATtiny261 461 861 这份资料介绍了执行Attiny261 461 861微控制器系列正弦波驱动三相无刷直流电动机霍尔传感器。-ATtiny261 461 861 The information on the implementation of microcontroller Attiny261 461 861 series three-phase sine wave driving brushless DC motor Hall sensor.
zhuchengxu
- 直流电动机双极性可逆双闭环PWM控制程序-Reversible DC motor bipolar double-loop PWM control procedures
simulink
- matlab电力电子仿真图(直流电动机调速系统仿真实验)-matlab simulink with power electronic technologe
915pwm07.17.02
- LPC932为例:创建一个脉宽调制信号的定时模式6 由Christian Kulig ,飞利浦半导体12/06/02 导言: 在LPC932可以用来创建一个脉宽调制PWM信号。 这是一个模拟信号,只有2离散水平,例如0V 和5V和恒定时期。目前的价值在这个信号 某一点的时间成正比其占空比。这是 高一期的时间除以时期。它也可以被 计算出的平均价值在某一特定时期。那个 意味着低通滤波后, (如RC电路)的信号变得 模拟,实际值所控制的
zlddjjxtxcs
- 利用MATLAB编写的直流电动机机械特性测试-MATLAB prepared using DC motor mechanical properties testing
zlddjtstxcs
- 利用MATLAB语言编写的直流电动机调速特性测试程序和模型分析-The use of MATLAB language features of the DC motor speed control testing procedures and analysis
zlddjqd
- 利用MATLAB语言编写的直流电动机开环启动和闭环启动特性分析-The use of MATLAB language open-loop DC motor start-up and characteristics of the closed-loop start
zlddjzd
- 利用MATLAB语言编写的直流电动机制动特性分析的程序-The use of MATLAB language of DC motor braking characteristics of process
1_speed_control_pid
- 这个源码,将使用模式,制定从一个粗略模型到一个基于PID的负载直流电动机控制系统的离散实施。-In this chapter we will use model elaboration to go from a crude model to a discrete implementation of a PID based control system for a DC motor with load.
weijiyuanli
- 微机报告 直流电动机斩波调速控制 以8088cpu为核心,扩展8253定时器/计数器,产生1ms(PWM的周期的方波),作为8259的IRQ7的中断请求信号,在中断程序中,由8255B口(PB0脚)输出PWM脉冲,经驱动单元输出驱动直流电动机(起码有高、中、低三个速度,甚至可连续调速)。-c++
DSP_relative_code
- TMS320LF2407 相关代码:RS232通信程序,无刷直流电动机调速程序,直流电动机单极性可逆双闭环PWM控制程序等-TMS320LF2407 relevant code: RS232 communication program, brushless DC motor speed control program, reversible double-loop DC motor unipolar PWM control programs
2812BLDC
- TMS320F2812的永磁无刷直流电动机控制: 采用霍尔传感器实现三相无刷直流电动机的控制-TMS320F2812 permanent magnet brushless DC motor control: using Hall sensors to achieve the control of three-phase brushless DC motor
PMSM
- 采用TMS320F2812数字信号处理器实现无刷直流电动机控制的主程序。-Use of TMS320F2812 digital signal processor to achieve brushless DC motor control, the main program.
zhiliudianji
- 直流电动机闭环系统调速数字控制系统的设计 -DC motor speed closed-loop system the design of digital control system
motor-run
- 单片机控制电动机的资料大全,本文介绍了交流电机,步进电机,无刷直流电机的闭环控制,给出了软件资料。-Microcontroller to control the motor Sourcebook, this article describes the AC motor, stepper motors, brushless DC motor closed-loop control, given the software information.