搜索资源列表
laser0918
- 三个DS18b20测温点，三选二控制策略，485通信控制，自保持继电器控制，at89c2051控制-3 DS18b20 temperature measurement points, three selected two control strategies, 485 communication control, self-holding relay control, at89c2051 control
schandpcb
- 使用Mega16单片机，两种数码管LG8016AH和TS8012AG，有键盘控制，继电器输出，和行程开关触发，带蜂鸣器驱动。-a sample use avr mega16,sch and pcb for you1
HB96FHB96N
- 转速测量电路，可测量霍尔传感器、编码器、光电传感器的信号输出，具有1路继电器输出-Speed measuring circuit, measurable, Hall sensors, encoders, photoelectric sensor signal output, with a road relay output
jdq
- 用VB开发的通过51单片机控制继电器开关的程序，-VB developers with the passage of 51 SCM control relay switch procedure,
c1
- 我上传的5个文件都是在单片机下运行的 主要是中断 通讯 继电器驱动 时钟 等 -I uploaded 5 files are running under the SCM was mainly driven clock interrupt communications relay
c2
- 我上传的5个文件都是在单片机下运行的 主要是中断 通讯 继电器驱动 时钟 等-I uploaded 5 files are running under the SCM was mainly driven clock interrupt communications relay
c3
- 我上传的5个文件都是在单片机下运行的 主要是中断 通讯 继电器驱动 时钟 等-I uploaded 5 files are running under the SCM was mainly driven clock interrupt communications relay
c4
- 我上传的5个文件都是在单片机下运行的 主要是中断 通讯 继电器驱动 时钟 等-I uploaded 5 files are running under the SCM was mainly driven clock interrupt communications relay
Cross-Layer
- 在这论文中，我们提出了跨层设计共同纳入 继电器的选择和最佳功率分配策略，以提高 合作网络寿命，大大降低整体 功耗。- In this paper, we proposed a cross-layer design jointly incorporating best relay selection and power allocation strategies to increase the cooperative network lifetime while minim
qrs
- 通过串行口，提示用户输入倒计时时间(0~999秒)； 时间设定完成后提示用户选择控制方式：“倒计时开”还是“倒计时关”； 若用户选择 “倒计时关”，继电器立即吸合，并倒计时直到时间为0时关断继电器； 若用户选择“倒计时开”，继电器暂不吸合，等倒计时时间为0时再吸合继电器； 倒计时时间通过串口送上位机(每秒更新一次)； 倒计时结束时蜂鸣器鸣响2秒作为提示； -Through the serial port, prompts the user to enter th
counter
- 外部脉冲输入，计算脉冲个数，实现参数计数器,可保存实时数，三极管输出和可控硅输出，继电器输出-counter
VALVEC
- PIC16873无线模块控制继电器，可根据收到的命令闭合或断开继电器完成简单的控制功能-PIC16873 wireless module control relays can be closed based on the receipt of orders or disconnect relay to complete a simple control functions
50seconddelay
- 数码管50秒倒计时程序,从49每秒倒计时达到0显示,再循环.可以是灯电路，继电器吸合等，或者执行一个程序-Digital control 50 seconds countdown procedures, from 49 second countdown to reach 0 shows that recycling. Can be a lamp circuits, relays, etc. Pick-up, or the implementation of a program
jidianqi
- 用51单片机控制继电器的工作和工程需要，控制准确安全！-Microcontroller with 51 control relays and engineering needs, control, safety and accurate!
optoisolatedrelaydrivercontrolofDCmotor
- Proteus单片机仿真实例 光耦隔离控制继电器驱动直流电机-Proteus MCU simulation example opto isolated relay driver control of DC motor
MicrocontrollerBasedElectronicCodeLockDesign
- 设计以电磁继电器模拟密码锁，由单片机8051来控制锁的打开与闭合，由HD7279来管理器键盘及显示，密码从键盘输入，用8051来控制7279显示当前锁的状态信息及报警。本次设计用单片机开发系统来模拟密码锁的多种功能，密码由4-6位数字组成，当输入密码相符时开锁，输入三次不符报警，同时密码输入正确时可以修改密码，此时指示灯亮。开锁单片机开发出开关量，通过光电耦合器控制，打开密码锁。报警则由单片机发出报警信号，控制音频放大电路发出报警声音。-Designed to simulate electrom
Uart_V3
- 开发环境 KEiL C 单片机 华邦W77E58 功能 串口收到“0”使P1口的灯流水闪烁，收到“1”停止，还有继电器有动作。另外加了W77E58特有的看门狗程序。-Winbond MCU development environment KEiL C function serial W77E58 receive a " 0" so that P1 mouth water flashing lights, receive a " 1" to stop,
djs
- 按SW19独立按键，倒计时开始 倒计时期间 继电器吸合 按SW20键继电器断开 计时暂停 按板上单片机复位按键 计数值恢复为999 此计数初值 可在程序中修改。-Press SW19 independent button during the countdown to begin the countdown relay pull-off time by SW20 key relay suspended by the board microcontroller counts reset butto
vbfx
- 可实现上位机对三菱FX系列PLC的监控，包括启动、停止、修改暂存器的值以及中间继电器的状态等，附带源码供大家学习。-Host computer can be realized on the Mitsubishi FX Series PLC controls, including start, stop, modify the value of the register, as well as the middle of the state of relays and so on, with so
Control_4
- 315遥控，控制4路继电器开关,系统最多可控制16路继电器-315 remote control, control 4-way relay switch, the system can control up to 16 relays