搜索资源列表
VxWorks-PCI-Driver
- 介绍VxWorks下PCI设备驱动的编写,不包括详细的源代码-PCI device driver under VxWorks introduces the preparation, does not include source code for details
linux-usbdriver
- linux下面 usb设备驱动 单字节发送 usbm9.26.c 读写成功,把接口程序中read的count参数作为输出参数 demo26.c 测试程序-linux usb device driver following single-byte read and write successfully sent usbm9.26.c, the interface program in the count parameter read the test procedure as output p
USB_code
- usb设备驱动程序源代码,usb设备驱动程序源代码-usb device driver source code, usb device driver source code
globalfifo_async
- linux 字符设备驱动-globalfifo_async-linux driver--globalfifo_async
driver
- WDM驱动,多串口卡硬件设备驱动 windows driver model-WDM driver, multi-port card hardware device drivers windows driver model
Linux-driver-development15
- 作者:华清远见嵌入式学院。《Linux设备驱动开发详解》(08&09年度畅销榜TOP50)第15章、Linux的I2C核心、总线与设备驱动。I2C总线仅仅使用SCL、SDA这两根信号线就实现了设备之间的数据交互,极大地简化了对硬件资源和PCB板布线空间的占用。因此,I2C总线被非常广泛地应用在EEPROM、实时钟、小型LCD等设备与CPU的接口中。Linux系统定义了I2C驱动体系结构,在Linux系统中,I2C驱动由3部分组成,即I2C核心、I2C总线驱动和I2C设备驱动。这3部分相互协作,形
ModBusTcp数据转发设备
- MCGS modbus TCP数据转发设备驱动。(MCGS Modbus TCP data forwarding device driver.)
naan1993-guns-master
- 设备驱动程序,用于采集现场设备,其他的我也不知道(Device drivers used to collect field equipment, and I don't know anything else)
Linux下I2C设备驱动开发和实现
- I2C驱动介绍,详细描述了linux下I2C驱动原理(I2C driver introduced, described in detail under the I2C driver Principle Linux)
ENC28j60程序
- 单片机驱动 设备驱动程序,平台 stm32(enc28j60 drivers for stm32)
04PWM驱动步进电机实验
- 04PWM驱动步进电机实验c语言编程, PWM生成,本设备 PWM 使用 16MHz 作为脉冲基准, 使用分频系数决定 PWM 脉冲频率, 使用占空比系数决定 PWM 脉冲的占空 * 比。 对应关系如下: * 频率 = 16000000 / 分频系数( Hz) 公式 1 * 占空比=占空比系数 / 分频系数 公式 2 * 分频系数范围是 2~65535, 因此理论上输出的最低频率是 16000000/65535=244.14Hz, 最高频率是 8000000Hz, 也就是
28_i2c总线之二设备和驱动注册
- Linux系统下I2C总线的设备驱动注册(I2C driver registration)
McgsSdk
- MCGS脚本驱动开发,凑够20个字,留下功与名(MCGS scr ipt driven development)
lpc5411x_xpresso54114_keil_iar_v3.00c.001_42
- NXP 新的双核心系列:LPC5411x 系列的外设驱动代码.(LPC5411x Peripheral driver code.)
PL2303驱动
- pl2302驱动1.用USB线连接学习板和电脑。随后会听到叮咚一声。并弹出一个对话框。 2.关闭该对话框。运行光盘中PL2303文件夹下 HL2303。按提示进行操作即可 3.安装成功后会在设备管理器 COM口选项中看到连接的COM口是多少 4.打开STC_ISP软件 选择芯片型号,COM口 5.切记 点击下载后冷启动下学习板。即关闭电源,在重新打开下(1. use the USB line to connect the learning board and the computer.
CanToUsb
- 实现windos下自定义USB设备的驱动(Customizing the driver of the USB device in windos)
《pci总线设备开发宝典》的附带光盘
- 《pci总线设备开发宝典》很好介绍PCI window 驱动的开发,对寄存器介绍、操作、以及通过driverstudio开发驱动的全部流程。(The "PCI bus device development book" provides a good introduction to the development of the PCI window drive, the introduction and operation of registers, and all the p
linux驱动之设备树
- linux驱动之设备树,华清远见教学课件(Device tree driven by Linux)
WDM设备驱动程序开发(武安河)配套光盘
- 键盘模拟,windows下通过c、c++实现的键盘usb驱动编程(Keyboard simulation, USB driver programming of keyboard realized by C and C + + in Windows)
ch374驱动
- CH374是一个USB总线的通用接口芯片,支持USB-HOST主机方式和USB-DEVICE/SLAVE设备方式,内置3端口HUB根集线器,支持低速和全速的控制传输、批量传输、中断传输以及同步/等时传输。在本地端,CH374具有8位数据总线和读、写、片选控制线以及中断输出,可以方便地挂接到单片机/DSP/MCU/MPU等控制器的系统总线上。除此之外,CH374还提供了节约I/O引脚的SPI串行通讯方式,通过3线或者4线SPI串行接口以及中断输出与单片机/DSP/MCU/MPU等相连接。(CH37