搜索资源列表
jianpanjiance
- 51单片机上可运行的键盘检测功能程序,查表、延时等。-Can run on 51 single-chip the keyboard detection program, a look-up table, and delay.
pwm_45khz
- 使用51单片机(晶振为12MHZ)产生PWM驱动信号 使用延时的方式,频率可以达到45KHZ,-51 microcontroller (crystal 12 MHz) generates the PWM drive signal delay, the frequency can reach 45kHz,
zhf2013
- 基于51单片机延时爆破系统 可设置时间-Based on 51 single-chip system can set the time delay blasting
keyboard
- 扫描行列键盘 实现无延时消抖 是应用于51单片机的程序-Scanning Array Keyboard debounce achieved without delay
test18b20
- 由于DS18B20是单线操作,所以必须严格遵守它的时序要求才能正常与之建立联系并实现读写操作。 网上见到的多是程序多是在主程序中以延时的方式实现,而且要求关中断,以实现18B20对时序的要求。但是实际应用中,测温操作一般是作为辅助动作,主要任务是通信及数据处理等其他操作,这样一来,如果将DS18B20的程序代码放在主程序中,势必影响其他需要实时处理的中断。 前些天玩到DS18B20,就尝试以51定时中断的方法实现DS18B20时序,在面包板上成功跑了起来。 用的
18b20
- 在这个实验中最重要的是时序,因为要精确到us,所以找到合适的延时函数很重要。之前网上有一些关于51的和PIC的精确延时函数,我试了下,还要去仿真,很不方便,后面搞了很久发现了一个很好的延时函数,我已经把它用红色标注出来了,抓好了延时,这程序基本没什么问题了。-In this experiment is the most important thing in sequence, because want to us, so it s very important to find a suitabl
51stc
- 2.4G延时代码 DS18N02温度传感器LCD液晶显示MAX232串口模块NRF24L01模块2.4G无线TR24模块2.4G无线等很多51单片机模块代码-2.4G delay code DS18N02 temperature sensor LCD display MAX232 serial module NRF24L01 Module 2.4G Wireless Module 2.4G Wireless TR24 51 microcontroller module code, and man
rs232
- 51单片机延时函数 外层循环n次 内层循环110次-51 single delay function of the outer loop n times the inner loop 110
e
- 基于51单片机的简易电子琴,能利用所给键盘的1,2,3,4,5,6,7,8八个键,能够发出7个不同的音调,而且有一个按键可以自动播放歌曲,要求按键按下时发声,松开延时一小段时间,中间再按别的键则发另外一音调的声音,当系统扫描到键盘按下,则快速检测出是哪一个按键被按下,然后单片机的定时器启动,发出一定频率的脉冲,该频率的脉冲经喇叭驱动电路放大滤波后,就会发出相应的音调。如果在前一个按下的键发声的同时有另一个按键被按下,则启动中断系统。前面的发音停止,转到后按的键的发音程序。发出后按的键的音调。-5
MPU6050_2
- 该程序为stc12c5axx单片机的mpu6050 IIC通讯驱动程序,解压之后mpu6050即为工程文件,初学者可以直接在此基础之上修改代码,稍微入门一点的可以直接把需要的驱动文件拿出自己使用,普通51单片机可以修改IIC函数当中的延时函数直接使用-The program is stc12c5axx SCM mpu6050 IIC communication driver, the project file is then decompressed mpu6050, beginners can
38k.8951
- 使用51累单片机用定时器和延时产生38khz的可调占空比方波信号,源码程序,经过实测 -Use an adjustable duty cycle of 51 tired microcontroller generates a square wave signal 38khz, the source program with a timer and delay, measured through
delayAndjump
- 延时与跳转控制的51汇编源码,适合学习51的初学者-delay and control the source code compilation of 51, 51 for beginners learning
lesson3_2
- 用数码管显示0到F,学习51单片机的可以学习,用到编码和延时-With digital display 0 to F, 51 MCU can learn to learn, use and delay coding
GSM
- 基于51单片机,通过GSM模块短信遥控多路开关.购买的是联通的不记名卡,实测有效,但短信接受偶尔有10秒以内的延迟.-Based on 51 single-chip, via GSM SMS remote multiplexer module. Purchased Unicom anonymous card, the measured effective, but occasionally there is a delay accepting messages within 10 seconds
BEEP_MUSIC
- 在51单片机控制下,蜂鸣器实现音乐盒功能。延时程序,音符。-In the 51 MCU control, buzzer realize music box functionality. Delay program notes.
delayasm
- 单片机延时程序,最近做单片机程序的时候,需要若干段较为精确的延时。用C语言不容易做出,而且我用的是STC的单片机,每条指令与51相比所花的时间有差异。最后决定采用C语言中嵌入汇编的方式来解决。 -SCM delay procedure, recently made SCM process, the need for a more accurate delay several segments. With C language is not easy to make, and I use th
delayAndjump
- 延时与跳转控制的51汇编源码,适合学习51的初学者-delay and control the source code compilation of 51, 51 for beginners learning
twodanpianji
- 自写51单片机程序实现红绿灯读秒延时交替闪烁变换的单片机程序-Since writing program 51 single delay countdown lights flash alternately transform microcontroller program
Stand-alone-keyboard-control
- 独立键盘控制 c语言 键盘消抖延时 51单片机-C language independent keyboard control 51 single keyboard debounce delay
LED
- 51单片机点亮LED程序,学习延时函数的编写-51 single lit LED program, learning to write the delay function