搜索资源列表
8_7car_huoer
- 凌阳61单片机关于霍尔传感器的计数实验和液晶显示-Sunplus 61 Microcontroller Experiment on the Hall sensor count
s3c2440init
- arm9 s3c2440最详细的启动文件分析，理解了这个文件，就算是ARM入门了-the init.s is the file of s3c2440 inition file, if you want to learn arm,it is the first file you should read.
ADC
- LPC2148驱动ADC ----- A/D模数转换 这个工作区 每个工程包含3个配置选项 ISP_iFlash_Hex - 生成.Hex格式的目标文件 JLINK_iflash - 通过JLINK来烧写内部Flash的配置 JLINIX_iram - 通过JLINK来在内部RAM中调试 工程名: LCD ----- LCD(包含了中断） MMC ----- MMC卡读写 Uart ----- 串口通讯 USBMouse ----- USB
LCD
- LPC2148 drive LCD ----- A / D conversion module The work area Each project contains three configuration options ISP_iFlash_Hex - generated. Hex object file format JLINK_iflash - JLINK to the programming through the configuration of the intern
Uart
- LPC2148 drive LCD ----- A / D conversion module The work area Each project contains three configuration options ISP_iFlash_Hex - generated. Hex object file format JLINK_iflash - JLINK to the programming through the configuration of the intern
USBMouse
- LPC2148 drive LCD ----- A / D conversion module The work area Each project contains three configuration options ISP_iFlash_Hex - generated. Hex object file format JLINK_iflash - JLINK to the programming through the configuration of the intern
JLink_Linux_090804_tar
- J－Link for linux,segger出了J-Link 的Linux-J－Link for linux
Setup_JLinkARM_V414b
- ARM仿真器Jlink最新驱动，开发ST、NXP必备。-ARM emulator Jlink the latest drivers, development of ST, NXP necessary.
KElL
- Keil下用Jlink调试LPC2210外部FLASH的方法，验证可用-Keil LPC2210 under external FLASH with Jlink debugging methods, validation can be used
BEEP
- 基于LPC2148的仿真实例 蜂鸣器的测试 仿真器是 jlink v8-LPC2148 based on the simulation test buzzer is jlink v8 emulator
LCD_12864
- 基于LPC2148的 LCD2148的显示 用的是IAR+jlink V8-The LCD2148 display based on LPC2148 with the IAR+ jlink V8
RTC
- 基于LPC2148的 RTC通过串口发送到PC机查看 用的是IAR+jlink V8-Based on the RTC LPC2148 sent to the PC via the serial port using a machine view IAR+ jlink V8
J-Link
- J-Link用户指南,全部Jlink调试过程-J-Link User Guide, all Jlink debugging process
AN_119_FTDI_Drivers_Installation_Guide_for_Window
- This file is fot ft2232 jlink.
Setup_JLinkARM_V408l
- 该软件为jlink v7的驱动程序，对于v8也同样适用，主要用于嵌入式开发-The software driver for the jlink v7, v8 is also applicable for mainly used for embedded development ......
123
- Micro2440 开发板 的Jlink 的初始化文件-Micro2440 initial file on the Plantform of Jlink
JLINK
- 驱动程序,帮助将电路板通过仿真器成功与电脑相连.-Driver, to help the board through the emulator successfully connected to the computer.
JLinkRev2.0
- jlink在keil或iar环境下使用的方法，过程-jlink in keil iar environment or the method used, the process
LED
- 1设计要求 PC6,PC7,PD6,PD13 LED快速交替闪烁。 2 硬件电路设计 在开发板上通用I/O口PC6,PC7,PD6,PD13作为控制D1,D2,D3,D4的控制线。 3软件程序设计 根据设计任务要求，软件程序主要包括： (1) 配置GPIO口，将PC6,PC7,PD6,PD13配置为上拉输出模式。 (2) 延时控制相应端口的置位和复位。 4 运行过程 (1) 使用Keil uVision3 通过
SWD_stm32f103rbt6_set.
- MDK3.5下jlink SWD功能调试stm32f103rbt6设置-MDK3.5 function under jlink SWD debugging stm32f103rbt6 set. Pdf