搜索资源列表
LPC2_CANBlinky_V130
- The following Philips LPC2k CAN examples in this directory were provided by ESAcademy. LPC2_CANAll_V110: Receives all CAN messages in a receive queue. LPC2_CANFull_V110: Uses Full-CAN-like reception filtering. LPC2_CANBlinky_V130
LPC2_CANAll_V110
- The following Philips LPC2k CAN examples in this directory were provided by ESAcademy. LPC2_CANAll_V110: Receives all CAN messages in a receive queue. LPC2_CANFull_V110: Uses Full-CAN-like reception filtering. LPC2_CANBlinky_V130
LPC2_CANFull_V110
- The following Philips LPC2k CAN examples in this directory were provided by ESAcademy. LPC2_CANAll_V110: Receives all CAN messages in a receive queue. LPC2_CANFull_V110: Uses Full-CAN-like reception filtering. LPC2_CANBlinky_V130
UWB_Fifth_Order_Derivative
- Models UWB TX and RX using BPSK fifth derivative. MATLAB Release: R13 Descr iption: This m file models a UWB system using BPSK with the fifth order derivative of the gaussian pulse with correlation receiver and intgrator. -Models UWB TX an
UWB_BPSK_transreceiver
- MATLAB仿真uwb使用bpsk调制解调的发送(TX)和接收(RX)-MATLAB uwb bpsk use of modulation and demodulation of this (TX) and receive (RX)
2262TX
- rf tx coding for TX and RX
rfid_model
- A system simulation environment in Matlab/Simulink of RFID is constructed in this paper. Special attention is emphasized on the analog/RF circuit.Negative effects are concerned in the system model,such as phase noise of the local oscillator,TX-RX
smsc911x_xscale_v1.12
- smsc911x 网卡驱动 This the users/programmers guide for the LAN911x Linux Driver The following sections can be found below * Revision History * Files * Features * Driver Parameters * Rx Performance Tuning * Tested Platforms * Rx
OFDM-basedWirelessBroadBandSystemSimulator
- 基于OFDM的无线宽带系统仿真It contains mainly two parts, i.e. link-level simulator and system-level simulator. Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx. Comparing the differen
TX_RX
- 在c++builder环境下一个串口通信程序，包括界面的设计和串口通信函数的设计，实现了串口通信。在文件夹TX-RX中。
icuwb07submission
- 一个UWB仿真程序包，里面包含信号生成，信道模拟，Tx/Rx等模块。M-file
io
- ecos serial rx and tx
NewMsg-RF1100
- (1) 315、433、868、915Mh的ISM 和SRD频段 (2) 最高工作速率500kbps，支持2-FSK、GFSK和MSK调制方式 (3) 高灵敏度（1.2kbps下-110dDm，1％数据包误码率） (4) 内置硬件CRC 检错和点对多点通信地址控制 (5) 较低的电流消耗（RX中，15.6mA，2.4kbps,433MHz） (6) 可编程控制的输出功率，对所有的支持频率可达+10dBm (7) 支持低功率电磁波激活功能 (8) 支持传输前自动清理信道
tX+RX+Xmodem
- 标准的c代码，支持Xmodem的接受和发送，支持短线重传，而且随时都可以用ESC断开。功能强大。在4510上可以直接使用。
MYMIMO
- 文件来源： 我的毕设 仿真结果： 在窄带Rayleigh快衰落信道下几种检测方法的误码率性能比较 说 明： 参数tx，rx,L，EbN0可以根据需要更改。 tx，rx是收发天线数，根据需要取值就好了，一般研究2发2收和4发4收 EbN0是信噪比取值范围，根据需要选择吧。取得点多当然算得慢。 L影响结果的波动性和误码率所能达到的下限，L值取得越大图像越接近真实情况。如果 EbN0最大值有20dB那么误码率可以达到10负4次方建议L不低于10000。 使用
channel
- ofdm信道特性 Channel transmission simulator Channel transmission simulator ％ ％ inputs: ％ sig2 - noise variance ％ Mt - number of Tx antennas ％ Mr - number of Rx antennas ％ x - vector of complex input symbols (for MIMO, this is a matrix, wh
u-uart
- UART verilog TX/RX OpenCores share
fet440_uart11_38400
- Echo a received character, RX ISR used. Normal mode is LPM0. // USART1 RX interrupt triggers TX Echo. // Baud rate divider with 1048576hz = 1048576/38400 = ~27.31 (01Bh|03h) // ACLK = LFXT1 = 32768Hz, MCLK = SMCLK = default DCO = 32 x ACLK = 10
71477183OFDM-Tx-Rx
- ofdm simulation of tx and rx
stm32f105 CAN通讯
- CAN通讯驱动程序 希望对大家有用 STM32F105使用CAN1 和CAN2一起通讯(STM32F105 CAN RX TXhe double CAN test passes, the CAN1 receives the CAN2 output, and the CAN2 receives the CAN1 output)