搜索资源列表
usbcan
- 这个程序是本人对周立功的ARM 2200实验板开发的USB固件程序的第一部分，已能实现对USB的枚举，PC能识别USB设备了！其余的功能各位可以自行增加！-this procedure is my right, who ARM Week 2200 Experimental board USB firmware development process to the first part, has been able to achieve USB enumeration, the PC can re
usb code _dsp
- 基于2407＋D12的USB底层硬件固件程序-based on the 2407 + D12 underlying hardware USB Firmware
lqbd12fw
- usb固件程序，描述了pdiusbd12固件的编写-usb firmware and firmware descr iption of the preparation pdiusbd12
USB接口数据采集卡
- 这个接口卡程序负责采集低频音频信号，USB控制芯片采用AN2131QC。软件包括3个模块：Keil51编写芯片固件程序，vc++编写USB驱动程序和用户程序-the interface card collection procedures for low-frequency audio signals, control chips using USB Peripheral. The software includes three modules : the preparation Keil51
USB
- USB固件程序 keilc 编写 直接load即可经验证 可用-Proven USB firmware available
usb
- EZUSB开发总结-固件部分，包含EZUSB开发中固件设计，个人小结，适合初学者快速入门，包含FX2 Slave FIFO，Slave FIFO Firmware及一些资料 -EZUSB Development Summary- firmware part, including EZUSB development of firmware design, personal summary, quick start for beginners, including FX2 Slave FIFO, S
VC-USB
- 源码包括固件源码（keil c），驱动源码（vc6.0与driverstudio 3.1,DDK2600），应用程序源码（vc6.0）以及硬件原理图。-Including firmware source code (keil c), driver source code (vc6.0 and driverstudio 3.1, DDK2600), the application source code (vc6.0) and hardware schematics.
usb-fir-ware
- usb固件开发文档，同时涉及到USB协议栈，即USB协议栈和USB固件一个系列相关-usb firmware development documents, and related to the USB stack, USB stack, and USB is a series of firmware related
USB-firmware-
- 在Keil C51开发环境中开发USB固件程序的流程和源码-Development environment in Keil C51 USB firmware development process and source
a-firmware--USB-light-up-LED-
- 用于通过USB点亮LED灯的USB固件程序-a firmware used to a test about USB light up LED
PDIUSBD12-USB
- PDIUSBD12 USB固件编程与驱动开发,主要介绍飞利浦公司的PDIUSBD12芯片的固件编程与驱动开发-The PDIUSBD12 USB firmware programming and driver development, introduces the Philips PDIUSBD12 chip firmware programming and driver development
usb-firmware-upgrader-lpc214x_ALL
- LPC系列的USB固件更新代码，可以类似Bootloader的固化到芯片。-LPC series USB firmware update code, similar to the chip Bootloader cure.
cy7c68013-usb-gu-jian-dai-ma
- cypress公司的cy7c68013开发usb固件程序代码-the cypress cy7c68013 development usb firmware code
D12-USB-source
- D12 USB固件的源程序 熟练掌握D12的USB功能开发。-D12 USB firmware source master D12 USB functionality development.
USB-Drive
- 基于CY7C68013A的USB固件配置,可用于实际工程设计.采用的是外接FIFO设计.-USB firmware configuration based on CY7C68013A,Can be used for practical engineering design. The use of external FIFO design.
stm32-usb-bootloader
- STM32 USB 固件升级，有上位机，支持第二次开发- STM32 USB firmware upgrade, the PC has to support the development of the second
USB_升级
- LPC5411 USB固件升级，USB驱动开发(LPC5411 USB firmware upgrade, USB driver development)
Cy7c68031固件程序firmware
- 实现数据包的接收与转发，USB驱动，68013开发(Data packets receive and forward)
Cypress固件架构彻底解析及USB枚举
- 中文的详细介绍，对应按照此方式可轻松写出固件文件。
JLINK固件修复
- 1.使用USB线连接JLINK与PC机，以提供JLINK工作电源 2. 短接图中ERASE(A) 的两个过孔约5秒。断开ERASE(A)位置的两个过孔的短接。然后拔掉JLINK与PC间的USB线（注意先后顺序） 3.短接图中,TST(B)处的两个过孔 4.使用USB线连接JLINK与PC机，至少超过10秒后，拔掉USB线，停止给JLINK供电（说明：请确保此过程中，图中TST(B)处一直处于可靠的短接状态） 5.断开图中TST(B)处的短接 更新固件 安装Install AT91-